Abstract:Fatigue failure is recognized as the primary cause of tubular twist-off. Repeated cyclic bending loads and stress caused by dogleg severity, pipe weight and buckled drill pipes would result in drill string fatigue failure as seven twist-off accidents have been observed at large shallow dogleg sections in three deep wells with TVD (True Vertical depth) more than 5000m. Fishing jobs, plug-back and sidetracking operations were time-consuming and costly, while typical inspection and cumulative pumping hours can't determine the thresholds for preventing drill string fatigue failure in such scenario. This paper proposes the methodology for preventing drill string fatigue failure in deep wells with large shallow dogleg. The relative fatigue index prediction model is established based on drill string stress characteristics and crack propagation behavior, on the basis of which cumulative fatigue distribution of entire drill string in drilled or pre-drill intervals could be calculated. Considering the added cumulative fatigue for drill string from drilled intervals, methods and procedures including optimizing drilling parameters, reshuffling drill string, replacing with new drill string are proposed for preventing fatigue failure in pre-drill interval. One of the filed applications was carried out in one deep well, which suffered from two drill string failures consecutively with failure position at same large shallow dogleg section. The calculated cumulative fatigue index of the second failure based on actual drilling data was 1.0595, which verified the accuracy of established model for predicting drill string fatigue failure. Also, simulation results showed that cumulative fatigue index rose rapidly when drilling through large shallow dogleg section, which justified all failure positions occurred at same large shallow dogleg section. Cumulative fatigue distribution of entire drill string was determined after two consecutively failures, suggesting that the drill string would have had to been reshuffled constantly with shrinking drilling interval if the remaining well section had been drilled with used drill pipes. After replacing with new drill string, simulation showed that maximum cumulative fatigue index would have been less than 0.35 if the remaining well section had been drilled with RPM lower than 60r/min and ROP higher than 3m/h by reaching design depth. The remaining well section was drilled without accident by just one interval with actual RPM within 30-40r/min and ROP within 3-11m/h. The established model could serve as an effective method to evaluate cumulative fatigue distribution of entire drill string, based on which proposed methodology could help to prevent drill string fatigue failure for deep well with large shallow dogleg.

Is the drill pipe safe during drilling process?—A new method for evaluating drill pipe failure risk based on the Noisy-OR gate and bayesian network

Gas pipeline failure evaluation method based on a Noisy-OR gate bayesian network

Failure probability estimation for structures based on health monitoring data and Bayesian network

Operational risk analysis of blowout scenario in offshore drilling operation

Process system failure evaluation method based on a Noisy-OR gate intuitionistic fuzzy Bayesian network in an uncertain environment

Dynamic risk assessment of deepwater drilling using data-based and probabilistic approach

Application of Bayesian Networks in Quantitative Risk Assessment of Subsea Blowout Preventer Operations

Real-time Risk Analysis Method for Diagnosis and Warning of Offshore Downhole Drilling Incident

Mechanical model and probability analysis of buried pipelines failure under uniform corrosion

Towards a Fuzzy Bayesian Network Based Approach for Safety Risk Analysis of Tunnel-Induced Pipeline Damage

Failure risk assessment by multi-state dynamic Bayesian network based on interval type-2 fuzzy sets and leaky-weighted sum algorithm: A case study of crude oil pipelines

Dynamic risk assessment of plugging and abandonment operation process of offshore wells based on Dynamic Bayesian Network

Third-Party Damage Model of a Natural Gas Pipeline Based on a Bayesian Network

Dynamic failure probability analysis of urban gas pipeline network

Hybrid Dynamic Bayesian Network Method for Performance Analysis of Safety Barriers Considering Multi-Maintenance Strategies

Methodology for Preventing Drill String Fatigue Failure in Deep Well with Large Shallow Dogleg

Risk analysis and maintenance decision making of natural gas pipelines with external corrosion based on Bayesian network

A machine learning methodology for probabilistic risk assessment of process operations: A case of subsea gas pipeline leak accidents

Dynamic risk assessment of deep-water dual gradient drilling with SMD system using an uncertain DBN-based comprehensive method

Bayesian Network Model for Buried Gas Pipeline Failure Analysis Caused by Corrosion and External Interference.

Risk Assessment of Polar Drillship Operations Based on Bayesian Networks