Abstract:The moving bed biofilm reactor (MBBR) has certain advantages, such as high wastewater treatment efficiency, low maintenance and operating costs, and simple operation. It has emerged as a valuable option for small decentralized facilities. The filling ratio, aeration mode and aeration intensity are the main factors that affect the performance of MBBRs in wastewater treatment. However, the information that concerns the used criteria that pertain to the process design for the MBBR is not adequate. In this study, a three dimensional computational fluid dynamics (CFD) model was constructed and the maximum error was only 1.98%, which was much smaller than the traditional 2D-CFD model. The filling ratio, aeration mode and aeration intensity of MBBR were optimized by CFD model from the point of view of fluid mechanics. The results show that the fluidization performance of the filling is the best under the one-side aeration mode with 30% filling ratio. The cost-performance ratio of the reactor with 30% filling ratio was 1.53, 25% and 35% filling ratio were only 1.17 and 1.14 respectively. Increasing the aeration intensity could improve the fluidization performance. However, the effect of high aeration intensity on the fluidization performance of the carrier was limited and the energy consumption increased greatly. The results revealed that when the aeration intensity increased from 0.07 min-1 to 0.13 min-1, the proportion of the carrier area increased by 16.56%. The proportion of the carrier area with an aeration rate of 0.20 min-1 was only 4.23%, which is higher than 0.13 min-1. The main factors that control the fluidization of the carrier were the range of the flow zone and the flow velocity of the liquid. Increasing the range of the flow zone could facilitate the flow of the carriers. The critical value of the flow velocity of the liquid in the flow zone was 0.04 m/s. These results could guide the optimization design of the filling ratio and the aeration conditions and provide a theoretical basis for the application of MBBR.

Optimization of the Internal Circulating Fluidized Bed Using Computational Fluid Dynamics Technology

CFD Simulation and Hydrodynamics Characterization of Solids Oscillation Behavior in a Circulating Fluidized Bed with Sweeping Bend Return

Structural Parameter Optimization of Hydraulic Vertox Separator in Recirculating Biofloc Technology System Based on Computational Fluid Dynamics

CFD simulation of cross flow in multi-tubular fixed-bed reactor of industrial level

Improvement of Inner Components in Biological Fluidized Bed Reactors for Wastewater Treatment

Dynamic Characteristics of Solids Circulation Establishment in Laboratory and Industrial Circulating Fluidized Beds with Sweeping Bend Return

Control of Pressure Balance and Solids Circulation Characteristics in DCFB Reactors

Computational Fluid Dynamics-Discrete Element Method Investigation of Solid Mixing Characteristics in an Internally Circulating Fluidized Bed

Optimization of Fluidization State of a Circulating Fluidized Bed Boiler for Economical Operation

Advancements of the Fluidized Bed Fenton (FBF) Technology for wastewater treatment: Mechanism, mass and heat transfer

Improving wastewater treatment plant performance by applying CFD models for design and operation: selected case studies

Experimental Study of the Effect of Internals on Optimizing Gas–solid Flow in a Circulating Fluidized Bed

Numerical study of hydrodynamic characteristics in a moving bed biofilm reactor

Structure Optimization Of Cfb Reactor For Moderate Temperature Fgd

Optimization of multiple-chamber fluidized beds using coarse-grained CFD-DEM simulations: Regulation of solids back-mixing

Superior performance of a membrane bioreactor through innovative in-situ aeration and structural optimization using computational fluid dynamics

Application of Computational Fluid Dynamics for Optimization of Hydraulic Efficiency of Clearwell

CFD Simulation and Optimization of the Water Treatment Reactor by Electron Beam

Design and structural parameter optimization of Venturi-type microbubble reactor for wastewater treatment by CFD simulation

LES-DEM Investigation of Gas–solid Flow Dynamics in an Internally Circulating Fluidized Bed

Performance Improvement of a Circulating Fluidized Bed Boiler Through Flow Modifications in Primary Air Supply System