Abstract:Currently, layered Ni-rich cathodes of LiNi x Mn y Co z O 2 ( x ≥ 0.8) have gained significant attention for high energy density Li-ion batteries (LIBs) owing to their high specific capacity of ∼200 mA h g −1 within a limited voltage range. However, the large-scale use of these cathodes is severely limited by their poor structural stability, high surface reactivity, and severe capacity fading resulting from intergranular microcracks triggered by large volume changes and formation of rock salt in the highly de-lithiated state. Considering the demand for high specific capacity and high cycling stability cathodes, a core–shell oxide material 0.8LiNi 0.85 Mn 0.10 Co 0.05 O 2 –0.2Li 1.2 Ni 0.16 Mn 0.56 Co 0.08 O 2 (NR-CS) with a Ni-rich oxide core of LiNi 0.85 Mn 0.10 Co 0.05 O 2 (NMC85) and an outer shell of a Mn-based Li-rich Li 1.2 Ni 0.16 Mn 0.56 Co 0.08 O 2 oxide is synthesized. The NR-CS material delivered an initial discharge capacity of 212 mA h g −1 when cycled at 20 mA g −1 (0.1C rate) in the potential range of 2.8–4.3 V vs. Li with 89% capacity retention after 120 cycles when tested in half-cells using Li anodes. Additionally, we compared its performance with Ni-rich oxide NMC85 alone and with integrated materials of both Ni-rich and Mn-based Li-rich oxides (NR–LR). It was found that the Ni-rich oxide NMC85 cathodes could deliver a specific capacity of 216 mA h g −1 with around 67% capacity retention, and those comprising the Li and Mn-rich NMC material possessed a specific capacity of 140 mA h g −1 with 71.4% capacity retention when cycled under similar experimental conditions at 0.1C in the potential range of 2.8–4.3 V vs. Li after 120 cycles. Thus, the core–shell structure benefits from the high capacity of the core (Ni-rich NMC85) and surface chemical stability of the Mn-based Li-rich oxide. Moreover, when tested in full Li-ion cells with pre-lithiated graphite anodes, graphite‖NR-CS cells could provide a discharge capacity of about 170 mA h g −1 and an energy density of 274 W h kg −1 during 200 cycles when cycled at 0.5C rate. Thus, this study highlights the importance of the core–shell structure of Ni-rich NMC oxide cathodes over Ni-rich oxide or Li- and Mn-rich NMC cathodes in providing high capacity, higher rate and better cycling stability when charged up to 4.3 V in LIBs.

Novel design of core shell structure by NCA modification on NCM cathode material to enhance capacity and cycle life for lithium secondary battery

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Binary-compositional core-shell structure Ni-rich cathode material with radially oriented primary particles in shell for long cycling lifespan lithium-ion batteries

A Novel Synthesis Strategy to Improve Cycle Stability of LiNi 0.8 Mn 0.1 Co 0.1 O 2 at High Cut-off Voltages Through Core-Shell Structuring

Core-shell structure LiNi0.8Co0.1Mn0.1O2 cathode material with improved electrochemical performance at high voltage

Advantageous electrochemical behaviour of new core–shell structured cathodes over nickel-rich ones for lithium-ion batteries

Plasma-induced amorphous N-nano carbon shell for improving structural stability of LiNi0.8Co0.1Mn0.1O2 cathode

In Situsynthesis Of A Nickel Concentration Gradient Structure Of Ni-Rich Lini(0.8)Co(0.15)Al(0.05)O(2)With Promising Superior Electrochemical Properties At High Cut-Off Voltage

Synthesis Method for Long Cycle Life Lithium-Ion Cathode Material: Nickel-Rich Core-Shell LiNi0.8Co0.1Mn0.1O2

Double Conductor Coating to Improve the Structural Stability and Electrochemical Performance of LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode Material

In situ synthesis of a nickel concentration gradient structure of Ni-rich LiNi0.8Co0.15Al0.05O2 with promising superior electrochemical properties at high cut-off voltage

High structure stability and Li-conduction of LiNi0.8Co0.1Mn0.1O2 cathode co-coated by Al2O3 and LiNbO3 for high performance lithium-ion battery

(Invited) Delineating the Intricacies Involved in the Synthesis of Cobalt-Free High-Nickel Layered Oxide Cathodes for Lithium-Ion Batteries

Al2O3 coated single-crystalline hexagonal nanosheets of LiNi0.6Co0.2Mn0.2O2 cathode materials for the high-performance lithium-ion batteries

Synthesis of Single Crystal LiNi 0.92 Co 0.06 Mn 0.01 Al 0.01 O 2 Cathode Materials with Superior Electrochemical Performance for Lithium Ion Batteries

1D nanobar-like LiNi<sub>0.4</sub>Co<sub>0.2</sub>Mn<sub>0.4</sub>O<sub>2</sub> as a stable cathode material for lithium-ion batteries with superior long-term capacity retention and high rate capability

Surface Cobaltization for Boosted Kinetics and Excellent Stability of Nickel-rich Layered Cathodes

Substantial Doping Engineering in Layered LiNi 0.5+x Co 0.2−x Mn 0.3 O 2 Materials for Lithium-Ion Batteries

Enhanced lithium storage capability of Ni-rich LiNi0.9CoxMn0.1−xO2(0 ≤ x ≤ 0.1) cathode by co-operation of Al-doping and V-coating

A highly promising high-nickel low-cobalt lithium layered oxide cathode material for high-performance lithium-ion batteries

Improving the Performance of LiNi0.925Co0.065Mn0.01O2 via Ti4+& Nb5+ Co-Modifications