Abstract:The high melting point and thermal stability of MoWTaNbVTi x refractory high entropy alloys have prompted their potential for harsh temperature structure application. A low-cost manufacturing strategy is key to realizing this promise. Powder metallurgy is known to be a cost-efficient manufacturing route for manufacturing refractory alloys. Elemental distribution and phases that form during manufacturing are crucial to realize the desired properties. However, the phase evolution and elemental distribution in MoWTaNbVTi x refractory high entropy alloys manufactured via powder metallurgy (PM) have not been rationalized earlier. The present study focuses on the phase evolution and elemental distribution analysis in MoWTaNbVTi x manufactured by different PM approaches, pressureless sintering, hot isostatic pressing, and spark plasma sintering. A series of MoWTaNbVTi x were manufactured using different PM manufacturing methods. Using intensive X-ray diffraction, microstructure, and elemental analysis, we reveal the formation of face-centered cubic (FCC) (TiTaNb) 0.53 C 0.47 carbide and TiO x oxide phase in the nonequiatomic body-centered cubic (BCC) MoWTaNbV matrix in MoWTaNbVTi x . Interestingly, the liquid state sintering (LSS) yields a BCC_LSS matrix with a lattice parameter of 3.176 Å, differently than the solid state sintered (SSS) BCC_SSS matrix with a lattice parameter of 3.193 Å. The fraction of (TiTaNb) 0.53 C 0.47 and TiO x phases varies with titanium (Ti) composition and PM processing routes. Nickel (Ni), as the sintering activator, enhances Ti diffusion in the matrix. Also, the hardness of the MoWTaNbVTi x varies nonlinearly in a range of ~ 602 to approximately 911 Hv with the ratio of oxide and carbide fraction. The hardness obtained in the PM approach is significantly higher than that observed for cast MoWTaNbVTi x refractory high entropy alloys, reported in the literature.

Fabrication of a Mo based high temperature TZM alloy by non-consumable arc melting technique

Microstructure and Mechanical Properties of Unalloyed Molybdenum Fabricated Via Wire Arc Additive Manufacturing

Present Situation on the High Temperature Property of TZM Alloy

THE Research and APPLICATION OF TZM ALLOY

Microstructure and elevated-temperature mechanical properties of refractory AlMo0.5NbTa0.5TiZr High Entropy Alloy fabricated by powder metallurgy

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Investigation on the recrystallization and mechanical properties of a novel TZM alloy with heat treatment

Synthesis of hypoxia-high density TZM alloy based on mechanochemistry and particle size distribution theories

Method for preparing low-oxygen titanium-zirconium-molybdenum (TZM) alloy and application

Excellent High-Temperature Strength and Ductility of the ZrC Nanoparticles Dispersed Molybdenum

Understanding the phase evolution and elemental distribution in MoWTaNbVTix manufactured via powder metallurgical approach

Investigation of microstructure and tensile properties of as-processed TZM alloy at elevated temperature

Powder Fabrication and Laser Additive Manufacturing of MoSiBTiC Alloy

Pre-hydrogenation metallurgy for Ti-3Al-5Mo-4.5V alloy with high density and mechanical properties

Microstructure and mechanical properties of molybdenum-titanium-zirconium-carbon alloy TZM processed via laser powder-bed fusion

Design and development of low density, high strength ZrNbAlVTi high entropy alloy for high temperature applications

High Temperature Fatigue Behaviour of TZM Molybdenum Alloy under Mechanical and Thermomechanical Cyclic Loads

Nanostructured High-Strength Molybdenum Alloys with Unprecedented Tensile Ductility.

Thermal stability of microstructures and mechanical properties in a Fe-based Fe-Cr-Mn-Cu-Mo multi-component alloy

Evaluation of tensile property and strengthening mechanism of Zirconia reinforced molybdenum alloy

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys