Abstract:Aluminum coatings can provide galvanic cathodic protection for several metals and alloys. In order to be a suitable protective solution on structural components, the mechanical integrity must be preserved. In particular, the fatigue properties are a challenge for thermal spray protective coatings on mechanical structures. To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc sprayed protective coating, different surface preparations prior to arc spraying were considered. In the present work, a feasibility study was performed using laser ablation as a surface preparation technique before or during arc spraying of coatings through collaboration between the LERMPS laboratory in France, the National Research Council of Canada and the Royal Military College of Canada. Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate surface preparation techniques including laser ablation (PROTAL® process), grit blasting and shot peening. Results indicate that a combination of key conditions including using nitrogen as the arc spray gas, shot peening and proper laser energy density for ablation provides high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates. Les revêtements en aluminium peuvent fournir une protection galvanique cathodique à plusieurs métaux et alliages. Afin de constituer une solution protectrice adéquate pour les éléments de structure, le procédé d’application du revètement doit préserver l’intégrité mécanique du substrat. En particulier, les propriétés de fatigue constituent un défi pour les revêtements protecteurs par projection thermique sur les structures mécaniques. Pour examiner le problème de l’intégrité de la fatigue de l’alliage d’aluminium 7075 avec un revêtement protecteur appliqué par projection à l’arc électrique, on a considéré différentes préparations de la surface avant l’application. Dans le travail présent, on a effectué une étude de faisabilité en utilisant l’ablation laser comme technique de préparation de la surface avant ou pendant l’application à l’arc de revêtements, par l’intermédiaire d’une collaboration entre le laboratoire LERMPS en France, le Conseil National de la Recherche du Canada et le Collège Militaire Royal du Canada. On a évalué les propriétés de fatigue ainsi que de résistance d’adhérence de revêtements en aluminium, en relation avec les techniques de préparation de la surface du substrat, incluant l’ablation laser (procédé PROTAL®), le sablage au jet de sable et le grenaillage. Les résultats indiquent qu’une combinaison de conditions clés incluant l’usage de l’azote comme gaz de projection à l’arc, le grenaillage et une densité appropriée d’énergie du laser pour l’ablation fourni une résistance élevée à la fatigue de substrats d’alliage 7075 revêtus d’un revètement métallique . Les échantillons préparés sous ces conditions montrent une résistance à la fatigue similaire aux substrats non revêtus.

Coatings by arc spraying of nanocrystalline metallic wires on carbon steel surfaces: surface hardness, hydrophobicity, and residual stress

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Correlation between microstructure properties and the effect of WC addition on the interface, hardness and corrosion performance of thermally sprayed NiCrBSi-WC coating

The Effect of Annealing on Microstructure and High Temperature Erosion Property of Arc-Spraying Coatings Containing Nanosized Ceramic Powders

Microstructure and Wear Properties of Nanostructured Coatings Prepared by Wire Arc Spray

Effect of hot coil immersion cooling process on microstructure and properties of strip steel and oxide scales

Study on Microstructure and Properties of FeNiCr/Ni Coated Cr_3C_2 Coatings Deposited by High Velocity Arc Spraying

Mechanical Properties and Tribological Behaviour of Electroless Ni–P–Cu Coatings on Corrosion-Resistant Alloys under Ultrahigh Contact Stress with Sprayed Nanoparticles

Electrochemical development and characterisation of nanostructured Ni–Fe alloy coatings for corrosion protection

Microstructure and Properties of FeMnCrAl/Ni Coated WC Coatings Deposited by High Velocity Arc Spraying

ALUMINUM PROTECTIVE COATINGS - FATIGUE AND BOND STRENGTH PROPERTIES WITH RESPECT TO SURFACE PREPARATION TECHNIQUES: LASER ABLATION, SHOT PEENING AND GRIT BLASTING

Microstructure, electrochemical corrosion and corrosion mechanism of electroplated Ni–W alloy coating by DFT calculation

Microstructure and Corrosion Study on Friction Surfaced Aluminum Alloy Coatings over Mild Steel

Microstructure and wear behavior of WC-reinforced AlCoCrFeNiSi high entropy alloy coatings prepared by high-velocity arc spraying

Effect of Surface Roughness and Structure Features on Tribological Properties of Electrodeposited Nanocrystalline Ni and Ni/Al2O3 Coatings

Characterization of Al-Co-Cr-Fe-Mn-Ni High-Entropy Alloy Coating Fabricated onto AA5083 Using Wire-Arc Additive Manufacturing

Formation and investigation of the properties of FeWCrMoBC metallic glass coatings on carbon steel

Study on Microstructure and Thermal Fatigue of FeMnCrAl/WC Coatings

Influence of Heat Treatment on the Microstructure and Wear Properties of Arc-Sprayed FeCrAl/Al Coating

Surface Characteristic and Friction Behavior of Plasma Sprayed FeCoNiCrMo0.2 High Entropy Alloy Coatings on BS960 High-Strength Steel with Subsequent Shot Peening Treatment

Mechanical, Tribological, and Electrochemical Evaluation of NiCrAlMoFe Thermally Sprayed Coatings Subject to Post-treatments