Abstract:Light-weight metal matrix composites, especially magnesium-based composites, have recently become more widespread for high-efficiency applications, including aerospace, automobile, defense, and telecommunication industries. The squeeze cast AZ91 base material (AZ91-BM) and its composites having 23 vol.% short carbon fibers were fabricated and investigated. The composite specimens were machined normal to the reinforced plane (Composite-N) and parallel to the reinforced plane (Composite-P). All the as-casted materials were subjected to different tests, such as hardness, compression, and wear testing, evaluating the mechanical properties. Dry wear tests were performed using a pin-on-disk machine at room temperature under different applied wear loads (1−5 N) and different sliding distances (0.4461×104−3.12×104 m). The microstructures and worn surfaces of the fabricated AZ91-BM and the two composite specimens were investigated using a scanning electron microscope (SEM) equipped with an energy dispersive spectroscopy (EDS) advanced analysis system. The wear debris was collected and investigated also under the SEM. The results showed significant improvement in hardness, compressive strength, and wear resistance of the composite specimens (Composite-N and Composite-P) over the AZ91-BM. The compressive strength and wear resistance are more fibers orientation sensitive than the hardness results. When the fiber orientation is parallel to the sliding direction (Composite-N), the weight loss is somewhat lower than that of the fiber orientation perpendicular to the sliding direction (Composite-P) at a constant wear load of 2 N and the sliding distances of 0.4461×104, 1.34×104 , and 2.23×104 m. In contrast, the weight loss of Composite-P is lower than Composite-N, especially at the highest sliding distance of 3.12×104 m due to the continuous feeding of graphite lubricant film and the higher compressive strength. Plastic deformation, oxidation, and abrasive wear are the dominant wear mechanisms of AZ91-BM; in contrast, abrasive and delamination wear are mainly the wear mechanisms of the two composites under the applied testing conditions.

Tribological Characteristics of the Magnesium Matrix-Glassy Carbon Particles Composite Manufactured by Different Casting Methods

THE TRIBOLOGICAL CHARACTERISTICS OF Al-Si/GRAPHITE COMPOSITE

Mechanical and Tribological Behavior of Mg-Matrix Composites Manufactured by Stir Casting

Processing of Sliding Hybrid Composites with Aluminum Alloy Matrix Containing Solid Lubricants

Assessment of the Tribological Properties of Aluminum Matrix Composites Intended for Cooperation with Piston Rings in Combustion Engines

Friction, wear, and characterization of magnesium composite for automotive brake pad material

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Mechanical and Wear Behaviour of Nano-Fly Ash Particle-Reinforced Mg Metal Matrix Composites Fabricated by Stir Casting Technique

Tribological impact on borosilicate glass powder reinforced Al-MMC by variation of sliding velocity and the study of its machinability

Microstructure, Mechanical Properties and Wear Resistance of As-Cast Mg-3Al-1Ca-0.4Mn/Tip Magnesium Matrix Composites

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Comparative Evaluation of Tribological Effectiveness of Carbon- and Glass-Filled Polyamide Composites Using Submicromechanical Diagnostics of Surface Layers before and after Wear Tests during Dry Sliding Friction

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Enhancement in Tribological Characteristics of Friction Stir Processed AZ91D Alloy Composite Reinforced with Molybdenum Disulfide

Wear Characteristics of Mg Alloy AZ91 Reinforced with Oriented Short Carbon Fibers

Effect of Carbon in Fabrication Al-SiC Nanocomposites for Tribological Application

Microstructure, Mechanical and Wear Properties of Short Carbon Fiber-Reinforced AM50 Magnesium Matrix Composite

Wear Behavior of AlSi10Mg Alloy Produced by Laser‐Based Powder Bed Fusion and Gravity Casting

Enrichment in Fracture Ductility Tribological Characteristics of Magnesium-Based Nanocomposites Fabricated via Multi-pass Friction Stir Processing and Study of Significant Parameters

Wear Behavior of AZ31/Al2O3 Magnesium Matrix Surface Nanocomposite Fabricated via Friction Stir Processing

Evaluation of tribological parameters for boron carbide and graphite infused aluminium hybrid composite fabricated by stir casting technique