Abstract:Perovskite solar cells based on the inorganic/organic hybrid perovskite have attracted increasing attention over the past 3 years. Many studies have been done in this area. Controling the morphology of the perovskite film is an effective way to improve the photoelectric conversion efficiency of the devices. In our reserch, we studied the influence of structure and morphology of perovskite films on the performance of the organic-inorganic hybrid perovskite solar cells which prepared by a sequential deposition method. Mesoporous TiO2 scaffold were introduced as electron collecting layer. Lead iodide (PbI2) was then spin cast on the TiO2 scaffold. The PbI2 subsequently transformed into the perovskite (CH3NH3PbI3) by dipping the TiO2/PbI2 film into a solution of CH3NH3I. We studied the difference between the PbI2 film with or without drying under room temperature after spin-coating. Through drying under room temperature, larger pores formed in the PbI2 film. While without drying under room temperature, smaller and shallower pores formed in the PbI2 film. The results show that larger pores in PbI2 film leads to more complete transformation of PbI2 to CH3NH3PbI3 and larger CH3NH3PbI3 particles. CH3NH3PbI3 films were prepared with three different processes: (a) direct dipping the PbI2 film with smaller pores into the CH3NH3I solution; (b) direct dipping the PbI2 with larger pores into the CH3NH3I solution; (c) dipping the PbI2 with larger pores into the CH3NH3I solution after pre-wetting. The resulting CH3NH3PbI3 films were studied with SEM, UV-vis absorption spectrum and XRD. The particles size of the CH3NH3PbI3 are 150, 250 and 350 rim for process (a), (b) and (c) respectively. CH3NH3PbI3 films fabricated through process (a) show insufficient absorption due to the insufficient transformation of the PbI2. The pre-wetting procedure leads to slower reaction result in larger CH3NH3PbI3 particle size. Devices with proper size of CH3NH3PbI3 particles show the highest photoelectric conversion efficiency. An efficiency of 13.5% was achieved with a J(sc) of 17.8 mA/cm(2), a V-oc of 1.05 V and a FF of 72.5%.

Influence of SCN− moiety on CH3NH3PbI3 perovskite film properties and the performance of carbon-based hole-transport-layer-free perovskite solar cells

Calculation and Fabrication of a CH3NH3Pb(SCN)xI3−x Perovskite Film as a Light Absorber in Carbon-based Hole-transport-layer-free Perovskite Solar Cells

Influence of an SCN- moiety on the electronic properties of γ-CsPb(SCN)xBr3-x and the performance of carbon-based HTL-free γ-CsPb(SCN)xBr3-x perovskite solar cells

Tuning the A-site Cation and X-site Anion Composition of CH3NH3PbI3 Perovskite Material for Efficient Planar Perovskite Solar Cells

Efficient and reproducible CH3NH3PbI(3-x)(SCN)x perovskite based planar solar cells.

Influence of Structure and Morphology of Perovskite Films on the Performance of Perovskite Solar Cells

Anion effect on properties of Zn-doped CH3NH3PbI3 based perovskite solar cells

Enhanced Performance of CH3NH3PbI3−x Cl X Perovskite Solar Cells by CH3NH3I Modification of TiO2-perovskite Layer Interface

High Efficient Planar-Heterojunction Solar Cells Achieved by Using A Smooth Ch3nh3pbi3 Film Via A New Approach of Forming the Pbi2 Nanostructure Together with Strategically High Ch3nh3i Concentration

Efficient and Reproducible CH3NH3PbI3 Perovskite Layer Prepared Using a Binary Solvent Containing a Cyclic Urea Additive.

Synthesis of Copper Zinc Tin Sulfide Cu2ZnSnS4 (CZTS) Nanoparticles Doped Material with High Properties for CH3NH3PbI3 Perovskite Solar Cells

CH3NH3SnI3 : Superior Light Absorption and Optimized Device Architecture with 31.93% Efficiency

High‐Performance Planar Solar Cells Based On CH3NH3PbI3‐xClx Perovskites with Determined Chlorine Mole Fraction

Device Simulation of Inverted CH3NH3PbI3−xClx Perovskite Solar Cells Based on PCBM Electron Transport Layer and NiO Hole Transport Layer

Synergetic Effect of Chloride Doping and Ch3nh3pbcl3 on Ch3nh3pbi3-Xclx Perovskite-Based Solar Cells

Enhanced Electronic Structure, Phase, and Morphology of a CH3NH3PbI3 Perovskite Solar Cell Using Vanadium Copper Sulfide (VCuS) Nanoparticle Treatment

Enhanced Performance of Perovskite CH3NH3PbI3 Solar Cell by Using CH3NH3I as Additive in Sequential Deposition.

Microstructure Modulation Of The Ch3nh3pbi3 Layer In Perovskite Solar Cells By 2-Propanol Pre-Wetting And Annealing In A Spray-Assisted Solution Process

Influence of Organic Cations on Intrinsic Properties of Lead Iodide Perovskite Solar Cells

A facile spray-assisted fabrication of homogenous flat CH3NH3PbI3 films for high performance mesostructure perovskite solar cells

Growth of Compact CH3NH3PbI3 Thin Films Governed by the Crystallization in PbI2 Matrix for Efficient Planar Perovskite Solar Cells.