Abstract:A deep understanding of underlying processes and possible challenges is required for the development of ammonia-fueled solid oxide fuel cell (SOFC) systems. In this context, a detailed 3D multiphysics model of an ammonia-fueled SOFC is developed in the current study. Anode off-gas recirculation and nickel nitriding as two of the main aspects of ammonia-fueled SOFCs are investigated in the current study. The developed model is validated with experimental data under various conditions including direct and pre-cracked ammonia cases for various flow rates at different temperatures (700–850 °C ) as well as different recirculation rates. A good agreement is achieved between the model results and the measurement indicating that the physics are well captured. Furthermore, nickel nitriding as one of the main challenges in the direct ammonia-fueled SOFCs is addressed and qualitatively validated with experimental data. The model can explain the reduction of performance difference between direct ammonia-fueled SOFC compared to its pre-cracked counterpart by reducing the fuel flow rate (increasing fuel utilization) and increasing the operating temperature. The highest performance difference (5.87%) is observed at 700 °C and fuel utilization of 14%, and the lowest difference (0.05%) belongs to 850 °C and fuel utilization of 70% at 0.5 A/cm 2 . Anode off-gas recirculation is found to yield significant savings in ammonia fuel around 21–27% while a slight power reduction (0.34–0.88%) is observed by increasing the recirculation rate from 70 to 90% compared to the case without recirculation. Excessive amount of nitrogen in the high recirculation rates does not show a significant effect on the performance. Nickel nitriding is reduced by increasing the temperature and fuel utilization.

Modeling ammonia-fueled co-flow dual-channel protonic-ceramic fuel cells

A Two-Dimensional Analysis of Mass Transport in Proton Exchange Membrane Fuel Cells

Insight into the complex ammonia decomposition/oxidation kinetics in ammonia protonic ceramic fuel cells via elementary modeling

A single-phase, non-isothermal model for PEM fuel cells

Multi-Physical and Electrochemical Coupling Model for the Protonic Ceramic Fuel Cells with H+/e−/O2− Mixed Conducting Cathodes

A three-dimensional mixed-domain PEM fuel cell model with fully-coupled transport phenomena

A Three-Dimensional, Multicomponent, Two-Phase Model For A Proton Exchange Membrane Fuel Cell With Straight Channels

A two-phase flow and non-isothermal agglomerate model for a proton exchange membrane (PEM) fuel cell

Design and Modelling of 3D Bionic Cathode Flow Field for Proton Exchange Membrane Fuel Cell

Cfd Based Two-Phase Modelling of Proton Exchange Membrane Fuel Cell with Interdigitated Flow Field

A 3D Two-Phase Model for a Membraneless Fuel Cell Using Decomposition of Hydrogen Peroxide with Y-Shaped Microchannel

Modeling study of an air‐breathing micro direct methanol fuel cell with an extended anode catalyst region

Coupling Ammonia Catalytic Decomposition and Electrochemical Oxidation for Solid Oxide Fuel Cells: A Model Based on Elementary Reaction Kinetics

Modeling of Packed Bed Methanol Steam Reformer Integrated with Tubular High Temperature Proton Exchange Membrane Fuel Cell

A Dynamic Tanks-in-Series Model for a High-Temperature PEM Fuel Cell

Detailed 3D multiphysics modeling of an ammonia-fueled solid oxide fuel cell: Anode off-gas recirculation and Ni nitriding degradation

A 1 + 1-D Multiphase Proton Exchange Membrane Fuel Cell Model for Real-Time Simulation

Numerical Simulation of Multi-Channel Planar Solid Oxide Fuel Cell Unit by Integrating Continuum Micro-Scale Pen Sub-Model

Three-dimensional Modeling of Transport Phenomena in Proton Exchange Membrane Fuel Cell with Different Fluid Channel

Computational Fluid Dynamics Study on the High Temperature Proton Exchange Membrane Fuel Cell

Open-Source and Multi-Fluid Numerical Modeling of Proton Exchange Membrane Fuel Cell