Abstract:This article is focused on the experimental study of flexural properties in different multi-layer carbon fiber-reinforced polymer (CFRP) composites and correlations with the results of finite element method (FEM) simulations of mechanical properties. The comparison of the results shows the possibility of reducing the number of experimental specimens for testing. The experimental study of flexural properties for four types of carbon fiber-reinforced polymer matrix composites with twill weaves (2 × 2) was carried out. As input materials, pre-impregnated carbon laminate GG 204 T and GG 630 T (prepreg) and two types of carbon fiber fabrics (GG 285 T and GG 300 T (fabric)) were used. Multi-layer samples were manufactured from two types of prepregs and two types of fabrics, which were hand-impregnated during sample preparation. The layers were stacked using same orientation. All specimens for flexural test were cut with the longer side in the weft direction. Pre-impregnated carbon laminates were further impregnated with resin DT 121H. Carbon fabrics were hand-impregnated with epoxy matrix LG 120 and hardener HG 700. To fulfill the aim of this research, finite element method (FEM)-based simulations of mechanical properties were performed. The FEM simulations and analysis were conducted in Hexagon's MSC Marc Mentat 2022.3 and Digimat 2022.4 software. This paper presents the results of actual experimental bending tests and the results of simulations of bending tests for different composite materials (mentioned previously). We created material models for simulations based on two methods—MF (Mean Field) and FE (Finite Element), and the comparative results show better agreement with the MF model. The composites (GG 285 T and GG 300 T) showed better flexural results than composites made from pre-impregnated carbon laminates (GG 204 T and GG 630 T). The difference in results for the hand-impregnated laminates was about 15% higher than for prepregs, but this is still within an acceptable tolerance as per the reported literature. The highest percentage difference of 14.25% between the simulation and the real experiment was found for the software tool Digimat FE 2022.4 – GG 630 T composite. The lowest difference of 0.5% was found for the software tool Digimat MF 2022.4 – GG 204 T composite. By comparing the results of the software tools with the results of the experimental measurements, it was found that the Digimat MF 2022.4 tool is closer to the results of the experimental measurements than the Digimat FE 2022.4 tool.

Mechanical performance of GFRP laminates manufactured from deformed stitched and three-dimensional woven preforms

Understanding the Impact of Fibre Wrinkle Architectures on Composite Laminates Through Tailored Gaps and Overlaps

Evaluation and Defect Detection in L-Shaped GFRP Laminates by Infrared Thermography

Deformation and Fracture Mechanisms of Automated Fiber Placement Pre-Preg Laminates under Out-of-plane Tensile Loading

Mechanical performance of composites based on various three-dimensional woven-fibre preforms

Modeling on the Effect of Automated Fiber Placement Induced Gaps in Curved Composite Laminates

Design and manufacture of mould-free fibre-reinforced laminates with compound curvature

Experimental study on the mechanical behavior of laminates made by fiber steering: Influence of fiber angle and tow width

Experimental study for the effect of hole notched in fracture mechanics of GLARE and GFRP composites subjected to quasi-static loading

Mechanical Behavior and Damage Monitoring of Pultruded Wood-Cored GFRP Sandwich Components

Evaluation of the mechanical behaviour of tufted preforms

GLARE deformation in low-restraint state: Tensile and bending behavior

Flexural and sinking stiffnesses investigation of metal, glass fiber reinforced plastic and hybrid laminates through a semi‐experimental method

Effect of Manufacturing Defect on Mechanical Performance of Plain Weave Carbon/epoxy Composite Based on 3D Geometrical Reconstruction

Assessing pseudo-ductile behavior of woven thermoplastic composites under tension and bending

Comparison of Mechanical Property Simulations with Results of Limited Flexural Tests of Different Multi-Layer Carbon Fiber-Reinforced Polymer Composites

Mechanical Deformation Mechanisms in Knitted Fabric Composites

Evaluation on Material Behaviors of Pultruded Glass Fiber Reinforced Polymer (GFRP) Laminates

Evaluation of fatigue damage of woven GFRP laminate by dynamic properties

Large Deformation Bending of Single‐ply Fabric Reinforced Polymer Composite

Mechanical Performance of Foam-Filled Lattice Composite Panels in Four-Point Bending: Experimental Investigation and Analytical Modeling