Abstract:Despite the wealth of literature on the friction and wear behaviour of ceramics, their wear mechanisms are far from well understood. The need to develop a precise understanding of the wear mechanisms is imperative for the development of better wear-resistant ceramics. Particularly in alumina ceramics, grain coarsening has been found to improve the crack growth resistance characteristics. However, if the same would be beneficial for wear resistant applications has not been systematically investigated. To evaluate if there exists a strong grain size effect on abrasive wear mechanisms in ceramics, a series of tests were conducted under severe sliding contact conditions in an alumina ceramic. Unlubricated sliding wear tests were performed on alumina of three different grain sizes, 0.7, 5 and 25 μm, using a blunt conical diamond indenter of about 100-μm tip radius as the slider at room temperature under normal loads of 8–40 N and sliding distances up to 120 mm. The abrasive wear behaviour was characterised by measuring the wear volume and wear rate as a function of normal load and sliding distance. In addition, the friction behaviour was also studied simultaneously as a function of these two variables. The wear damage mechanisms were examined using both optical and electron microscopy as well as energy dispersive X-ray spectroscopy. For a given grain size and sliding distance, the width and depth of the worn track (hence wear volume) and the frictional force all increased with normal load. These observations were more markedly displayed in the coarse-grained than in the fine-grained alumina. In the 0.7-μm fine-grained alumina, the wear process appeared to be mainly controlled by plastic deformation especially at low loads (e.g. < 10 N). At higher loads, however, both plastic deformation and grain boundary fracture processes seemed to be involved. In the 5-μm and 25-μm coarse-grained aluminas, the predominant material removal process was controlled by both intergranular and transgranular fractures.

Abrasive Size Effect on Friction Coefficient of AISI 1045 Steel and 6061-T6 Aluminium Alloy in Two-Body Abrasive Wear

Friction and Wear Mechanisms of 316L Stainless Steel in Dry Sliding Contact: Effect of Abrasive Particle Size

Friction and Wear of Metals under Micro-abrasion, Wet and Dry Sliding Conditions

The effect of abrasive grain size on the transition between abrasive and adhesive wear

Effect of Impact Angle and Speed, and Weight Abrasive Concentration on AISI 1015 and 304 Steel Exposed to Erosive Wear

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

Grain size effect on abrasive wear mechanisms in alumina ceramics

The Effect of Wear Environment Temperature on the Wear Behavior and Friction Coefficient of SiCw/Al Composite

Influence of Particle Size on Microstructure and Sliding Wear Response of Fly Ash and Rice Husk Ash Reinforced Al6061 MMCs

Microstructure and Corrosion Study on Friction Surfaced Aluminum Alloy Coatings over Mild Steel

Effect of Silica Size on the Relative Wear of Microstructures Containing Solidification Carbides and Tempered Martensite Using a Dry Sand Rubber Wheel Test

Wear Analysis of Friction Stir Processed AA7075-SiC-Graphite Hybrid Surface Composites

Evaluation of Abrasive Wear Resistance of Al2O3/7075 Composite by Taguchi Experimental Design Technique

Effect of lubricant additives on the tribological behavior of aluminum alloy against steel

Effects of roughing, finishing, and aggressive machining conditions on the milling performance of AISI 1045 steel using TiAlN coated inserts

Friction and wear of titanium alloys sliding against metal, polymer, and ceramic counterfaces

Abrasive wear of alumina fibre-reinforced aluminium

Influence of wear parameters on friction performance of A356 aluminum – graphite/ granite particles reinforced metal matrix hybrid composites

Effect of abrasive particle size and the influence of microstructure on the wear mechanisms in wear-resistant materials

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Desirability based multiobjective optimisation of abrasive wear and frictional behaviour of aluminium (Al/3.25Cu/8.5Si)/fly ash composites