Abstract:A 12% Cr ferritic/martensitic steel, HT-9, has been used as a primary core material for nuclear reactors. The microstructure and mechanical properties of gas tungsten arc butt welded joints of HT-9 in as-welded, and as-tempered conditions have been explored. In as-welded condition, the fusion zone (FZ) contained a fresh martensite matrix with delta (δ)-ferrite. The δ-ferrite was rich in Cr and depleted in C compared with the matrix. The heat-affected zone (HAZ) could be divided into three areas as the distance from the fusion line increased: δ-ferrite/martensite duplex zone, fully recrystallized zone, and partly recrystallized zone. Prior austenitic grains did not coarsen in the δ-ferrite/martensite duplex zone due to the newly nucleated δ-ferrite grains and incompletely ferritizing (δ-ferrite) during the welding thermal cycle. The weldment microhardness distributed heterogeneously with values above 600 HV1.0 in the HAZ and FZ and 250 HV1.0 in the base metal (BM). Solute C in the matrix, induced by the dissolution of carbide during the welding process, dominated the microhardness variation. Low toughness was observed in the FZ with a quasi-cleavage fracture tested from − 80 to 20 °C. The tensile fracture occurred in the relatively soft BM tested from 20 to 600 °C. In as-tempered condition (760 °C for 1 h), M23C6-type carbides precipitated within the martensitic laths, the lath boundaries, and the δ-ferrite/martensite interfaces. Moreover, V, Cr, Mo-rich nitrides with very small size also precipitated in the δ-ferrite/martensite interface. The tempering treatment improved the homogenous distribution of weldment hardness significantly. Tensile fracture still occurred in the BM of the weldment specimens tested from 20 to 600 °C. The impact toughness improved significantly, but the ductile–brittle transaction temperature was − 12 °C which was higher than that of the normalized and tempered (N&T) BM. δ-ferrite was considered to be one of the major factors aggravating the impact toughness in the FZ.

Effect of filler addition on solidification behaviour and hot tensile properties of GTA-welded tube joints of Super 304H austenitic stainless steel

Microstructural Characterization and Grain Refinement of Ti-15 V-3Al-3Cr-3Sn Gas Tungsten Arc Welds by Ni- and Si-Modified Fillers

Influence of Filler Material on the Microstructural and Mechanical Properties of 430 Ferritic Stainless Steel Weld Joints

Cold Metal Transfer Welding of Ferritic and Austenitic Stainless Steel: Microstructural, Mechanical, and Electrochemical Studies

Influence of filler materials on GTAW dissimilar welds: Inconel 718 and austenitic stainless steel 304L

Effect of filler metal composition on microstructural and mechanical characterization of dissimilar welded joint of nitronic steel and super duplex stainless steel

Study on Effect of Nickel Molybdenum Coated Filler in Gas Tungsten Arc Welding

Investigations on microstructural characteristics and mechanical properties of 316 L stainless steel welded joints using nickel coated filler material by gas tungsten arc welding

Influence of Ni and PWHT on microstructure evolution and mechanical properties of GTA-welded duplex stainless steel and super duplex stainless steel joints: A comparative investigation

Influence of M-TIG and A-TIG Welding Process on Microstructure and Mechanical Behavior of 409 Ferritic Stainless Steel

Development of weld filler material to match the advanced martensitic heat resistance steel G115 and tailoring the performance by tempering temperature

Influence of filler wire composition and heat input on microstructure and strength of CMT brazed DP steel joints

Dissimilar autogenous TIG joint of Alloy 617 and AISI 304H steel for AUSC application

Combined Effect of Tungsten Inert Gas Welding and Roller Expansion Processes on Mechanical and Metallurgical Characteristics of Heat Exchanger Tube-To-Tubesheet Joints

Weldability of cast CoCrFeMnNi high-entropy alloys using various filler metals for cryogenic applications

A Study of Microstructure and Mechanical Properties for the Autogenous Single-Pass Butt Weldment of a Ferritic/Martensitic Steel Using Gas Tungsten Arc Welding

Effect of Precipitation Behavior and Deformation Twinning Evolution on the Mechanical Properties of 16Cr–25.5Ni–4.2Mo Superaustenitic Stainless Steel Weld Metals

Mechanical and micro-structural studies of pulsed and constant current TIG weldments of super duplex stainless steels and Austenitic stainless steels

Microstructure and mechanical properties of gas metal arc welded CoCrFeMnNi joints using a 308 stainless steel filler metal

Joining mechanism evolution of fusion welded TC4 titanium alloy/304 stainless steel dissimilar joint by GTAW

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints