Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Numerical analysis of the brick shape and bond pattern effects on the masonry cyclic behavior: a new brick shape to improve the masonry seismic performance

Experimental Study on Mechanical Properties of Basalt Fiber-Clay Lime Mortar and Application in Brick Masonry

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

3D hybrid modelling approach combining the finite and discrete element methods: Validation based on masonry shear wall tests

Numerical and Experimental Investigation on Cyclic Behavior of Masonry Infill Walls Retrofitted with CFRP

Comparative numerical study to simulate masonry with bed joint reinforced repointing

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method

Nonlinear Behavior of a Masonry Subassemblage Before and After Strengthening with Inorganic Matrix-Grid Composites

Experimental Research and Numerical Analysis of CFRP Retrofitted Masonry Triplets under Shear Loading

A robust computational strategy for failure prediction of masonry structures using an improved multi‐surface damage‐plastic based interface model

In-Plane Cyclic Behaviour Comparison of Adobe Wall Retrofitted by Mortar Enhanced by Physical and Chemical Methods

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Cyclic Behavior of Masonry Shear Walls Retrofitted with Engineered Cementitious Composite and Pseudoelastic Shape Memory Alloy

A block-based numerical strategy for modeling the dynamic out-of-plane behavior of unreinforced brick masonry walls

Numerical homogenization‐based seismic assessment of an English‐bond masonry prototype: Structural level application

Slip-enhanced plastic-damage constitutive model for masonry structures

Dynamic characteristics of stone masonry walls before and after damage: Experimental and numerical investigations

Seismic behavior of load-bearing horizontal-hole interlocking concrete block masonry walls: An experimental investigation of variable configurations

Evaluating the Role of Mortar Composition on the Cyclic Behavior of Unreinforced Masonry Shear Walls

Bond behavior of steel fiber-reinforced mortar (SFRM) applied onto masonry substrate