Abstract:The non-equilibrium phase evolution during laser powder bed fusion (LPBF) of AlSi10Mg alloy is thoroughly characterized and analyzed by means of advanced electron microscopy and analytical simulation of rapid solidification phenomenon. The evolution of microstructural strengthening agents such as inter-cellular eutectic phase and intra-cellular precipitates is presented in correspondence with the local variation of cellular/dendritic solidification patterns within a typical melt pool. The eutectic phase exhibits two different morphologies: lamellar and fibrous. As with the cell size variation, the overall volume fraction of eutectic phase and the lamella spacing is shown to gradually decrease by moving away from the melt-pool boundary (MPB), i.e., through crossing over from a coarse to a fine cellular zone. The eutectic-free regions within the α-Al cells contain a large number density of nano-sized precipitates that are predominantly Si-rich and are either fully or semi-coherent with the Al matrix. The formation of nano-precipitates is linked to the increased (non-equilibrium) solubility limits of α-Al cells due to the rapid solidification effect. For the first time, we identify such nano-precipitates with non-equilibrium crystal structures and morphologies: "Spheres" and "Ellipsoids" with Face Centered Cubic (FCC), and "Plates" and "Needles" with a Diamond Cubic (DC) superlattice structure that emerges from within the Al matrix. The microstructure in the heat-affected zone (HAZ) right underneath the MPB exhibits an absence of cell boundaries and eutectic phases while consisting primarily of large Si-rich and Mg-rich precipitates. Finally, the local variation of nano-hardness across a solidified melt pool is shown to correlate well with the corresponding profile of microstructural refinement, i.e., exhibiting a minimum at the HAZ and a peak at around the melt-pool centerline. The findings here can significantly advance the state of knowledge for the strengthening behavior in an as-built LPBF-processed AlSi10Mg alloy.

Equiaxed Grain Formation by Intrinsic Heterogeneous Nucleation Via Rapid Heating and Cooling in Additive Manufacturing of Aluminum-Silicon Hypoeutectic Alloy

Effect of Rapid Heating and Cooling Conditions on Microstructure Formation in Powder Bed Fusion of Al-Si Hypoeutectic Alloy: A Phase-Field Study

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Demonstrating the roles of solute and nucleant in grain refinement of additively manufactured aluminium alloys

Bulk Nanostructure Formation Directly From The Multicomponent Alloy Melt

Grain Refinement in A Alznmgcuti Alloy by Intensive Melt Shearing: A Multi-Step Nucleation Mechanism

Enhanced Heterogeneous Nucleation in Az91d Alloy by Intensive Melt Shearing

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Formation of Heterostructure with Appearance of α-Al Phase in Hyper- and Eutectic Al-Si Alloys by Solidification at High Rate

Revealing the Mechanisms for the Nucleation and Formation of Equiaxed Grains in Commercial Purity Aluminum by Fluid-Solid Coupling Induced by a Pulsed Magnetic Field

Three-dimensional morphology of an ultrafine Al-Si eutectic produced via laser rapid solidification

Promoting the columnar to equiaxed transition and grain refinement of titanium alloys during additive manufacturing

Intergranular precipitation and chemical fluctuations in an additively manufactured 2205 duplex stainless steel

Shear Enhanced Heterogeneous Nucleation in AZ91D Alloy

Hierarchical Grain Refinement During the Laser Additive Manufacturing of Ti-6Al-4V Alloys by the Addition of Micron-Sized Refractory Particles

Rapid Solidification and Non-equilibrium Phase Constitution in Laser Powder Bed Fusion (LPBF) of AlSi10Mg Alloy: Analysis of Nano-precipitates, Eutectic Phases, and Hardness Evolution

Mechanism of Grain Refinement in 3D-Printed AlSi10Mg Alloy Subjected to Severe Plastic Deformation

Fabrication of Fine Grain Structures in Al Matrices at Elevated Temperature by the Stimulation of Dual-Size Particles

Grain Refinement and Localized Amorphization of Additively Manufactured High-Entropy Alloy Matrix Composites Reinforced by Nano Ceramic Particles Via Selective-Laser-melting/remelting

Solidification microstructure manipulation mechanism of hypoeutectic and hypereutectic Al-Si alloys controlled by trace in-situ nano-Fe 2 B and nano-Fe 3 Si

Unravelling heterogeneities in sub-grain cellular structure and micromechanical response of additive manufactured Ti-Nb alloys