Abstract:The Li1.4Al0.4Ti1.6(PO4)3(LATP) nanocrystal powder is synthesized by citric acid assisted sol-gel method.The LATP powder is crystalized at 850℃ for 4 h,and the X-ray diffraction patterns show that the NASICON structure is obtained without any impurity phase.The LATP films are prepared by tape casting method through using as-synthesized LATP powder and subsequently recrystalized at various temperatures for 5 h.The impedance spectra of LATP film recrystalized at various temperatures indicate that the film sintered at 950℃ has the highest lithium ionic conductivity. Meanwhile,it is demonstrated that no impurity exists in LATP film recrystalizated at 950℃,and its lattice parameters are a=b=8.50236 Å and c=20.82379 Å.The high-purity LATP-epoxy films are prepared by modification with epoxy resin.The water permeation test proves that the LATP-epoxy film can prevent water from penetrating for 15 d,which indicates that epoxy resin fills the holes in LATP film.The fracture surface topography of LATP-epoxy film shows its dense structure with grain sizes from nano-scale to micro-scale.The energy dispersive X-ray spectrometer mapping of the fracture of LATP-epoxy film indicates that the carbon elements are uniformly distributed in grain boundary,which means that epoxy resin is soaked into LATP film.The relative density of 89.5% is obtained for LATP film,which is increased to 93.0% for LATP-epoxy (the nominal density is around 2.9624 g/cm3).The difference in relative density between LATP film and LATP-epoxy film indicates that the epoxy resin is immersed in LATP film already.The total,bulk,and grain boundary lithium ionic conductivities for the LATP film at 25℃ are 8.70×10-4 S·cm-1,2.63×10-3 S·cm-1 and 1.30×10-3 S·cm-1,respectively.The total,bulk,and grain boundary lithium ionic conductivities for the LATP-epoxy film at 25℃ are 3.35×10-4 S·cm-1,1.84×10-3 S·cm-1 and 4.09×10-4 S·cm-1,respectively.The decrease in the total conductivity of the LATP-epoxy film may be caused by the increase in its grain boundary resistance and its exposure to the atmosphere during modification with epoxy resin.The high lithium ionic conductivity for both LATP film and LATP-epoxy contributes to homogeneous mixture at sol-gel process and the decreasing of grain boundary impedance for this special structure.The activation energies for LATP film and LATP-epoxy film are 0.36 eV and 0.34 eV,respectively, based on Arrhenius equation.The water-impermeable high lithium ion conducting solid electrolyte of LATP modified with epoxy resin is likely to be used as protective film for lithium metal electrode of novel high energy density batteries.

Li-ion conducting Li0.35La0.55TiO3 electrolyte thick films fabricated by aerosol deposition

Tape-Casting Li0.34La0.56TiO3 Ceramic Electrolyte Films Permit High Energy Density of Lithium-Metal Batteries

Solid State Reaction Synthesis and Characterization of Lithium Lanthanum Titanate Lithium-Ion Conducting Solid Electrolyte with Different Li to La Content

Li1.4al0.4ti1.6(Po4)(3) High Lithium Ion Conducting Solid Electrolyte Prepared by Tape Casting and Modified with Epoxy Resin

Physical and electrochemical characterization of amorphous lithium lanthanum titanate solid electrolyte thin-film fabricated by e-beam evaporation

Robust and Manufacturable Lithium Lanthanum Titanate-Based Solid-State Electrolyte Thin Films Deposited in Open Air

Preparing Two-Dimensional Ordered Li0.33 La0.557 TiO3 Crystal in Interlayer Channel of Thin Laminar Inorganic Solid-State Electrolyte towards Ultrafast Li+ Transfer

Increasing Ionic Conductivity in Li 0.33 La 0.56 TiO 3 Thin-Films Via Optimization of Processing Atmosphere and Temperature

Preparation and Characterization of Lithium-Ion-Conductive Li1.3al0.3ti1.7(Po4)(3) Thin Films by the Solution Deposition

Preparation and performance of novel LLTO thin film electrolytes for thin film lithium batteries

Electrochemical Performance and Kinetic Behavior of Lithium Ion in Li4Ti5O12 Thin Film Electrodes

Structure and Conductivity of Perovskite Li0.355La0.35Sr0.3Ti0.995M0.005O3 (M = Al, Co and In) Ceramics

Preparation and Electrochemical Properties of Li4Ti5O12 Thin Film Electrodes by Pulsed Laser Deposition

Ionic conductivity properties of amorphous Li–La–Zr–O solid electrolyte for thin film batteries

Li-ion Diffusion Kinetics in LiCoPO4 Thin Films Deposited on NASICON-type Glass Ceramic Electrolytes by Magnetron Sputtering

Effect of Sr and Nb co-doped on the total conductivity of Li0.5La0.5TiO3 ceramic electrolytes

Synthesis of textured Li0.33La0.55TiO3 solid electrolytes by molten salt method

TiO2 phase-controlled synthesis of Li-La-TiO solid electrolytes for advanced all-solid-state batteries

Microstructure and ionic conductivity of Li0.5-La0.5(Ti1-Nb )O3 solid-state electrolytes

The molding of the ceramic solid electrolyte sheet prepared by tape casting

Room-temperature fabrication of garnet-type solid-electrolyte: Optimizing particle size for high ionic conductivity