Abstract:The concept of grain boundary engineering (GBE) has been proposed based on the fact that many studies have demonstrated that boundaries associated with low Sigma-value coincident site lattice (CSL) misorientations show higher resistance to intergranular fracture and corrosion, reduced susceptibility to impurity segregation and superior ductility. It is commonly accepted that for fcc metals of low to medium stacking fault energy metals, including Ni and many Ni-alloys, the most important CSL boundary for the GBE process is a Sigma 3 boundary, the occurrence of which is dominated by the formation of annealing twins. Moreover, it has been found that repetitive thermo-mechanical processing can be used to increase further the fraction of Sigma 3 (and Sigma 3(n) (n >1)) boundaries. However, the mechanism for this is not yet clear. Therefore, an investigation on the evolution of Sigma 3 boundaries during recrystallization is important for understanding the mechanisms of GBE for those materials. In the present paper the evolution of Sigma 3 boundaries during recrystallization in a 96% cold-rolled sample of pure nickel of 99.996% purity has been explored using orientation maps obtained using electron backscatter diffraction (EBSD). Each orientation map was taken from the same area after annealing for various times. Based on the EBSD data the Sigma 3 boundaries can be divided into two groups: "twin" type and "non-twin" type. These groups can be differentiated using a parameter of deviation angle (Delta theta) of boundary misorientation to the ideal twin misorientation (60 degrees < 111 >). During recrystallization incoherent twin boundaries are found to develop from coherent twin boundaries. It is also that most Sigma 3(n) (n >1) boundaries are formed by impringement of a nucleus with its n-order twins, and that the chance for such impingement events decreases significantly with increasing n. Most non-twin type Sigma 3 boundaries arise from impingement of Sigma 1 and twin type Sigma 3 boundaries. Non-twin type Sigma 3 boundaries may be more effective than twin type Sigma 3 boundaries to develop a beneficial grain boundary network.

Controlled Evolution of Coincidence Site Lattice Related Grain Boundaries

Coordinated grain boundary deformation governed nanograin annihilation in shear cycling

In Situ Atomistic Observation of Grain Boundary Migration Subjected to Defect Interaction

Microstructural evolution during grain boundary engineering of low to medium stacking fault energy fcc materials

Evolution of Sigma 3 Boundaries During Recrystallization of Cold-Rolled Nickel Deformed to High Strain

Understanding the Formation and Evolution of Low-Angle Grain Boundaries in Nickel-Based Single Crystal Superalloys

Grain Boundary Engineering of a Low Stacking Fault Energy Ni-based Superalloy

Role of Coincident Site Lattice Boundaries in Creep and Stress Corrosion Cracking

Effect of Short-Range Ordering on the Grain Boundary Character Distribution Optimization of FCC Metals with High Stacking Fault Energy: A Case Study on Ni-Cr Alloys

In Situ Ebsd Observation of Grain Boundary Character Distribution Evolution During Thermomechanical Process Used for Grain Boundary Engineering of 304 Austenitic Stainless Steel

Deformation and boundary motion analysis of a faceted twin grain boundary

Cut-off deviation for CSL boundaries in recrystallized face-centered cubic materials

Influences of Symmetric Tilt Grain Boundary on the Stretching Deformation Behaviors of Cu Bicrystals

Grain refinement at the nanoscale via mechanical twinning and dislocation interaction in a nickel-based alloy

Recrystallization behavior and grain boundary character evolution in Co-Cr alloy from selective laser melting to heat treatment

Grain Boundary Processes in Strengthening, Weakening, and Superplasticity

Analysis of grain boundary networks and their evolution during grain boundary engineering

Synergistic effects of temperature and strain rate on tensile properties of simulated Ni-6Cu alloy with Σ3 non-Arrhenius grain boundary

Influence of Grain Boundary Segregation on the Deformation Behavior of Nanocrystalline Ni50Co50 Solid Solution Alloys Investigated by Molecular Dynamics Simulations

Grain Boundary Elimination by Twinning and Dislocation Nucleation in Front of Intergranular Crack Tips in BCC Iron

Interface engineering at the nanoscale: Synthesis of low‐energy boundaries