Abstract:With the advancement of science and technology and the construction of metal-based composites (MMC), it became possible to achieve improved properties that were not easily available in an alloy. In fact, with the emergence of such technology, manufacturers were able to adjust the resulting materials according to their needs in such a way as to provide mechanical strength, hardness, corrosion resistance, or other desired properties. These composites were used in various aerospace, automotive, construction, and production industries. Aluminum-based composites are among the structures that have taken an important place in the industry due to their lightweight and high strength. The present study produced bi-alloy aluminum-based 1060/5083 composites fabricated with alumina particles with a Hot ARBp at T = 380 °C. Also, the effect of rolling steps on the roll bonding mechanism is investigated using numerical simulation. As the novelty of this study and for the first time, a bi-alloy 1050/5083 composites reinforced Al 2 O 3 particles via ARB process have been produced and then, potential dynamic polarization in 3.5 Wt% NaCl solution was used to study the corrosion properties of these composites. The corrosion behavior of these samples was compared and studied with that of the annealed aluminum. The study aimed to investigate the bonding behavior between the bi-alloy layers. So, as a result of enhancing influence on the number of ARBp, this experimental investigation revealed a significant enhancement in the main electrochemical parameters and the inert character of the Alumina particles. Reducing the active zones of the material surfaces could delay the corrosion process. Results showed that the corrosion resistance of the sample fabricated after six steps improved more than 100 % in comparison with the initial annealed Al alloy. Also, the average peeling force improved from 45 N to 94 N for the sample fabricated with six steps. Moreover, at a higher number of steps, the corrosion of MMC improved. Moreover, increasing the number of ARBsteps illustrated an improvement in the wear resistance of samples. Finally, the samples' bonding interface, corrosion surface, and peeled surface were investigated using scanning electron microscopy (SEM).

Effect of Film Formation Potential on Passive Behavior of Ultra-Fine-Grained 1050 Al Alloy Fabricated via ARB Process

Corrosion Behavior of Ultra-fine Grained 1050 Aluminum Alloy Fabricated by ARB Process in a Buffer Borate Solution

Microstructural Evolution and Mechanical Properties of Multi-layered Aluminum Alloy 6061 Processed by Accumulative Roll Bonding

Corrosion and mechanical properties of Al/Al 2 O 3 composites fabricated via accumulative roll bonding process: Experimental and numerical simulation

Enhancing grain refinement and mechanical properties of AA1100/MgAZ31/AA1100 composites by using different roll bonding techniques

Microstructure of Commercial-Purity Aluminum Sheets Processed by Accumulative Roll Bonding (ARB) at a Series of Cyclic Preheating Conditions

The Effects of Cold Rolling and Stabilization Treatment on the Improvement of Microstructure, Mechanical Properties, and Corrosion Behavior of AA5083 Sheet

Anisotropic Behavior of Al1050 through Accumulative Roll Bonding

Enhancing of aluminum alloy 1050-H4 tensile strength by accumulative roll bonding process

Correlation Between Microstructure, Mechanical Properties, and Corrosion Characteristics of AZ31 Mg Alloy Processed by Accumulative Roll Bonding Process

The effect of heat treatment on the microstructure and electrochemical corrosion behavior of multilayer AA6061 alloy fabricated by additive friction stir deposition

Forming limit diagrams and mechanical properties of AA1050/Ti CP2 multilayered composite produced by the accumulative roll bonding technique

Microstructural evolution and mechanical properties of multilayered ARB6/3/6 2N Al processed by accumulative roll bonding

On the impact of using alumina nanoparticles and initial aging on the microstructure and mechanical properties of the AA1050/AA2024 nanostructure composite, created by accumulative roll bonding (ARB) method

The Passive Film Characteristics of Several Plastic Deformation 2099 Al–Li Alloy

Microstructure Evolution and Mechanical Properties of AZ31 Alloy with Accumulative Roll Bonding

Tailoring nanostructured, graded, and particle-reinforced Al laminates by accumulative roll bonding

Effect of Asymmetric Accumulative Roll-Bonding process on the Microstructure and Strength Evolution of the AA1050/AZ31/AA1050 Multilayered Composite Materials

Enhancement of strength and ductility in 6061Al alloy processed by cross accumulative roll bonding

Interfacial Bonding and Fracture Behaviors of AZ63 Magnesium Alloy Sheet Processed by Accumulative Roll Bonding

Comprehensive investigation on wear and microstructure development in Al/ti ultrafine grained multi-layered composite produced by Accumulative Roll Bonding (ARB)