Abstract:NUREG report CR-6909 [1] proposed in 2007 new rules for evaluating environmental effects in fatigue analyses of new reactors components. These new rules, based on simple correlations, consider that Fen penalty factors (ratio of fatigue life in air at room temperature to that in water at service temperature) are mainly function of strain rate, temperature, sulfur content and dissolved oxygen concentrations. In order to evaluate the conservatisms included in the NUREG report CR-6909, discriminating Low Cycle Fatigue (LCF) tests were performed on a 304L austenitic stainless steel in PWR environment using various modified loading signals deduced from a representative loading strain history as close as possible to actual transients. Using the strain rate integral method recommended in the NUREG/CR-6909, the expected Fen penalty factors evaluated for each modified representative loading signal was close to 6, while the experimental Fen penalty factors measured were strongly dependent of the shape of the loading signals. Experimental Fen penalty factors obtained for the various modified loading signals vary from ∼ 1.5 to ∼ 4. These discriminating LCF tests performed on polished specimens demonstrate that the detailed strain integral method cannot correctly predict the actual environmental effects for the various shapes of loading signals deduced from a representative loading strain history. Other LCF tests were also performed for various constant strain amplitudes using fully reverse triangle signals for comparison purpose with tests performed by other laboratories. It appears that, contrary to published results, environmental effects decrease when the strain amplitude decreases from 0.6% until 0.2%. In the case of the strain amplitude of 0.6%, the Fen penalty factor formulation proposed in the NUREG report CR-6909 is accurate while, for lower strain amplitude of 0.2%, the Fen penalty factor formulation is very severe. It appears that the application of the NUREG/CR-6909 including the Fen model proposed by ANL (Argonne National Laboratory) for austenitic stainless steel provides excessive margins compared to penalty factors as observed experimentally. From this experimental program, conservatisms included in the NUREG/CR-6909 methodology appear to be excessive and can lead to fatigue design issues.

Generation of Low Cycle Fatigue Design Data for Nitrogen Enhanced 316LN SS as per RCC-MR Code

Creep properties and design curves for nitrogen enhanced grade of 316LN stainless steel

Nitrogen Enhanced 316LN Austenitic Stainless Steel for Sodium Cooled Fast Reactors

Effect of strain rate on low cycle fatigue of 316LN stainless steel with varying nitrogen content: Part-II fatigue life and fracture

Low Cycle Fatigue Behavior of 316LN Stainless Steel Alloyed with Varying Nitrogen Content. Part II: Fatigue Life and Fracture Behavior

The Effect of Nitrogen Alloying on the Low Cycle Fatigue and Creep-Fatigue Interaction Behavior of 316LN Stainless Steel

Evolution of creep resistant 316 stainless steel for sodium cooled fast reactor applications

Strain controlled fatigue deformation and fracture of nitrogen alloyed 316LN austenitic stainless steel

Low Cycle Fatigue Behavior of 316LN Stainless Steel Alloyed with Varying Nitrogen Content. Part I: Cyclic Deformation Behavior

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

Influence of nitrogen alloying on dynamic strain ageing regimes in low cycle fatigue of AISI 316LN stainless steel

Creep–fatigue interaction behavior of 316LN austenitic stainless steel with varying nitrogen content

Influence of Secondary Cyclic Hardening on the Low Cycle Fatigue Behavior of Nitrogen Alloyed 316LN Stainless Steel

Creep strengthening of low carbon grade type 316LN stainless steel by nitrogen

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Effect of Loading Signal Shape and of Surface Finish on the Low Cycle Fatigue Behavior of 304L Stainless Steel in PWR Environment

Effect of strain rate on low cycle fatigue of 316LN stainless steel with varying nitrogen content: Part-I cyclic deformation behavior

Effect of nitrogen on high temperature low cycle fatigue behaviors in type 316L stainless steel

Cyclic Deformation and Low-Cycle Fatigue for 316LN Stainless Steel under Non-proportional Loading