Abstract:The paper considers the influence of the parameters of the plasma spraying process on the technological characteristics of multilayer coatings based on nickel-chromium, nickel-chromium-aluminum-yttrium materials, oxide ceramics, intended for operation at high temperature and additional dynamic loads. The design of plasma coatings during their application (with subsequent high-energy processing) under such conditions requires a comprehensive solution – both the use of high-quality powder ingredients and the optimization of technological parameters. The plasma process of applying powder materials has been improved to obtain the maximum values of their utilization factors. The technological characteristics that affect the properties of plasma coatings are optimized, namely: the flow rates of the plasma-forming and materials-transporting gases, the flow rate of supplied powder materials, the current and voltage of the electric arc of the plasma torch, the distance from the plasma torch nozzle exit to the substrate. The paper presents the results of studies of the structure of coatings, performed using scanning electron microscopy. Their analysis has made it possible to form general regularities obtained by the action of radiation of compression plasma flows on coatings formed by air plasma. The considered structures are created using the processes of melting, compaction and high-speed cooling of plasma coatings. The main optimization indicators are the maximum local compaction and spillage of the obtained compositions with the absence of defects and destruction from the impact of compression plasma flows. The main effect during the action of radiation of a compression plasma flow on previously formed coatings is thermal. It contributes heating of the near-surface layer. When the coating is exposed to radiation of compression plasma flows, a remelted layer of oxides with a thickness of about 12–15 μm is created, smoothing the relief of the formed surface and creating a network of cracks on the surface, diverging into the depth of the coating. The liquid-phase processes occurring in the molten phase of the near-surface layers after exposure to compression plasma radiation change the structure of the layers and contribute to the modification of their mechanical properties. By smoothing the surface, increasing the density of the surface crystallized layer and minimizing macro-defects – pores or macrocracks – the mechanical characteristics of the coatings increase.

Dielectric Coating Deposition Regimes during Electron-Beam Evaporation of Ceramics in the Fore-Vacuum Pressure Range

Some Oxide-Films Deposited By Reactive Low-Voltage Plasma-Assisted Evaporation

Two-Layer Nanocomposite TiC-Based Coatings Produced by a Combination of Pulsed Cathodic Arc Evaporation and Vacuum Electro-Spark Alloying

Electron beam evaporation of boron at forevacuum pressures for plasma-assisted deposition of boron-containing coatings

Ion Composition of the Beam Plasma Generated by Electron-Beam Evaporation of Metals and Ceramic in the Forevacuum Range of Pressure

Characteristics of a Source for Oxide Coating Deposition by the Electron-Beam Evaporation of Dielectric Materials

Deposition of dielectric films on silicon using a fore-vacuum plasma electron source

Metastable Phase Formation, Microstructure, and Dielectric Properties in Plasma-Sprayed Alumina Ceramic Coatings

A Mechanism for the Growth of a Plasma Electrolytic Oxide Coating on Al

Thermionic coating method with preliminary bombardment of the substrate surface with a stream of low energy ions

Magnetron sputtering and electron beam evaporation systems for pure boron thin film coatings

Electron-Beam Synthesis and Modification and Properties of Boron Coatings on Alloy Surfaces

Modification of ZrO 2 ceramic by continuous and pulsed electron beams in the forevacuum pressure range

Plasma sprayed alumina-yttria composite ceramic coating for electrical insulation applications

Chromium arc plasma characterization, structure and properties of CrN coatings prepared by vacuum arc evaporation

Aerosol Deposition for Ceramic Thick Film Formation at Room Temperature

Multi-Layers Composite Plasma Coatings Based on Oxide Ceramics and M-Croll

Discharge System with a Self-Heated Hollow Cathode and an Evaporating Anode in a Cusp Magnetic Field for Oxide Coatings Deposition

Coatings-electrodes for processing dielectric aluminum oxide ceramics on a wire electrical discharge machine

Electron-Beam and Plasma Oxidation-Resistant and Thermal-Barrier Coatings Deposited on Turbine Blades Using Cast and Powder Ni(Co)CrAlY(Si) Alloys Produced by Electron Beam Melting IV. Chemical and Phase Composition and Structure of Cocralysi Powder Alloys and Their Use

Electron Beam Formation and its Effect in Novel Plasma-optical Device for Evaporation of Micro-droplets in Cathode ARC Plasma Coating