Abstract:Transition metal based high entropy alloys (HEAs) are often used in electrocatalytic (water electrolysis) applications due to the synergistic effect operating among its constituent elements and unpaired electrons in d orbitals of the concerned metal. In this study, a low cost NiMnFeCu high entropy alloy was successfully synthesised using the combined techniques of mechanical milling (MA) and vacuum sintering. X-ray diffraction was used to analyse the phase composition, optical microscopy, and scanning electron microscopy were used to characterise the fabricated material’s microstructure and chemical homogeneity, thermal, and mechanical properties were tested using the differential scanning calorimetry method and a universal testing machine, respectively. Electrochemical workstation was used to carry out preliminary electrochemical studies such as linear sweep voltammetry (LSV), cyclic voltammetry (CV) and chronoamperometry. The results showed that the as- sintered NiMnFeCu HEA possessed a single- phase FCC structure. The HEA NiMnFeCu sintered at 1050 °C (S4) and 1000 °C (S2) with a holding time of 2 h showed a yield strength of 516.3 MPa and 389.8 MPa, respectively, and the micro-hardness values were measured to be 233.45 ± 9 HV and 198.7 ± 8 HV, respectively. Preliminary electrochemical studies proved that the alloy sintered at 1000 °C (S2) with a holding time of 2 h exhibited excellent electrocatalytic properties with a measured overpotential of 322 mV at 10 mA cm−2 at 100 cycles of CV and good stability for 10 h when compared to state-of-the-art electrocatalytic materials IrO2 and RuO2. This suggested that the HEA NiMnFeCu fabricated under the condition S2 could potentially be used for industrial-scale water electrolysis as it possesses permissible mechanical and good electrochemical properties.

Characterizations of High Entropy Alloy Powder as Catalyst Synthesized by Mechanical Alloying for Azo Dye Degradation

Development of High Entropy Alloy (HEA) as Catalyst for Azo Dye Degradation in Fenton Process

Development of a Novel High-Entropy Alloy with Eminent Efficiency of Degrading Azo Dye Solutions

Development of a novel (Ni40Fe30Co20Al10)90Ti10 high-entropy alloy with excellent photocatalytic performance

Improving the Degradation Efficiency for the Azo Dye of Fe82Si2.5B12P2.5C Alloy Via Heat Treatment

Rapid decoloration of azo dye Direct Blue 6 by AlCrFeMn high entropy alloy

Enhanced Degradation Performance of Fe75B12.5Si12.5 Amorphous Alloys on Azo Dye

The Degradation Performance of the Fe78Si13B9 and (feconi)78si13b9 High-Entropy Amorphous Alloy Ribbons

Progress and prospects of Mg-based amorphous alloys in azo dye wastewater treatment

Efficient Catalytic Degradation of Azo Dyes from Textile Wastewater by Nano and Micro Amorphous Alloys

Fabrication, Microstructure, Mechanical, and Electrochemical Properties of NiMnFeCu High Entropy Alloy from Elemental Powders

Optimizing Mechanical Properties of Fe26.7Co26.7Ni26.7Si8.9B11 High Entropy Alloy by Inducing Hypoeutectic to Quasi-Duplex Microstructural Transition.

Enhanced photocatalytic abilities of innovative NbTaZrMoW high-entropy alloys (HEAs): a comparative analysis with its high entropy oxide (HEO) counterpart

Alloying and corrosion characteristics of FeNiMnCu-based high entropy alloys

Alloying behavior and characterization of (CoCrFeNiMn)90M10 (M=Al, Hf) high-entropy materials fabricated by mechanical alloying

Microstructural evolution of CrCuFeNiZn nanocrystalline high entropy alloy prepared by mechanical alloying

A green approach for decolorising azo dyes by using AlCrFeMn-based high-entropy alloys doped with nonmetallic elements (S, P and C)

Nanostructured Al–Ti–Fe–Mn–Ni High-Entropy Alloy by Mechanical Alloying: Synthesis and Characterization

Amorphous Alloys, Degradation Performance of Azo Dyes: Review

Microstructure evolution and catalytic activity of AlCo1−xFeNiTiMox high entropy alloys fabricated by powder metallurgy route

Preparation of FeCoNiCrMn High Entropy Alloy by Electrochemical Reduction of Solid Oxides in Molten Salt and Its Corrosion Behavior in Aqueous Solution