Abstract:Fibre-reinforced high-performance fly ash foam concrete (FHFC) has broad engineering application prospects owing to its lightweight and high-strength, energy-saving, heat preservation and environmental protection characteristics. Its mechanical properties and constitutive models can serve as an important basis for engineering structural design, numerical analysis and structural reliability monitoring. Aimed at exploring the influence of different factors on the physical and mechanical properties of FHFC and its stress–strain constitutive relationship, the dry density, cube compressive strength, splitting tensile strength and axial compressive strength of 27 groups of FHFC with different mixture proportions were measured and analysed. The primary and secondary relationships of the water–binder ratio, sand–binder ratio and replacement rate of fly ash to cement on the physical and mechanical properties of FHFC were studied. The failure mechanism of FHFC under uniaxial compression was discussed and a two-stage phenomenological constitutive model of FHFC was established through theoretical derivation. The results show that sand–binder ratio and water–binder ratio are the main factors affecting the physical and mechanical properties of FHFC. The stress–strain curve shows the characteristics of stages, namely, the elastic–plastic stage, the stress upswing stage, the plastic plateau stage and the failure stage. The influence of each factor on the elastic–plastic stage of the stress–strain curve shows obvious regularity, but the influence on the plastic stage is complex, and the regularity is not significant. The established two-stage phenomenological constitutive model is in good agreement with the stress–strain curve obtained from the test, and it can more accurately predict the uniaxial compression response of FHFC. The model can be used for the theoretical calculation of the bearing capacity of high-strength foam concrete structural members and even serve as an important basis for the engineering application of high-strength foam concrete. The influences of various factors on the performance of fibre-reinforced high-performance fly ash foam concrete were investigated. The uniaxial compression failure mechanism and stress–strain curve of fibre-reinforced high-performance fly ash foam concrete in different test groups were analysed. A two-stage phenomenological constitutive model suitable for fibre-reinforced high-performance fly ash foam concrete was established.

Impact of particle size of fly ash on the early compressive strength of concrete: Experimental investigation and modelling

Prediction of compressive strength development for blended cement mortar considering fly ash fineness and replacement ratio

Influence of Mineral Admixture on Early-Age Concrete Cracking

The Influence and Application of Slag, Fly Ash, and Limestone Flour on Compressive Strength of Concrete Based on the Concrete Compressive Strength Development over Time (CCSDOT) Model

Investigating the Impact of Fly Ash on the Strength and Micro-Structure of Concrete during Steam Curing and Subsequent Stages

Mechanical properties and constitutive model of fibre-reinforced high-performance class-F fly ash foam concrete

Modeling of Effect of Fly Ash Amount on Microstructure and Chloride Diffusivity of Blended Fly Ash-Cement Systems

The Relationship of Compressive Strength and Chemically Bound Water Content of High-Volume Fly Ash-Cement Mortar

Effects of Fly Ash Particle Size and Chemical Activators on the Hydration of High-Volume Fly Ash Mortars

Compressive behavior and microstructural analysis of low and high volume fly ash concrete containing recycled concrete aggregate

High-volume ultrafine fly ash-cement slurry mechanical properties and strength development model establishment

Experimental study on the compressive strength and shrinkage of concrete containing fly ash and ground granulated blast‐furnace slag

Systematic multiscale models to predict the compressive strength of fly ash-based geopolymer concrete at various mixture proportions and curing regimes

Strength, Permeability and Multiscale Pore Characteristics of Cement-Based Materials with High-Volume Fly Ash Contents and Different Water-Binder Ratios

Predicting the chloride diffusion in concrete incorporating fly ash by a multi-scale model

The Differences among the Roles of Ground Fly Ash in the Paste, Mortar and Concrete

Experimental Investigation and Numerical Model for Chloride Diffusivity of Long-Age Fly Ash Cement Slurry

Evaluation of Mechanical and Microscopic Properties of Magnesium Phosphate Cement-Based Concrete with Different Fly Ash Additions

The Influence of Ground Fly Ash on Cement Hydration and Mechanical Property of Mortar

Research on mechanical properties of concrete by nano-TiC-BF-fly ash

The Effect of the Addition of Coal Fly Ash (CFA) on the Control of Water Movement within the Structure of the Concrete