Abstract:Fibre-reinforced high-performance fly ash foam concrete (FHFC) has broad engineering application prospects owing to its lightweight and high-strength, energy-saving, heat preservation and environmental protection characteristics. Its mechanical properties and constitutive models can serve as an important basis for engineering structural design, numerical analysis and structural reliability monitoring. Aimed at exploring the influence of different factors on the physical and mechanical properties of FHFC and its stress–strain constitutive relationship, the dry density, cube compressive strength, splitting tensile strength and axial compressive strength of 27 groups of FHFC with different mixture proportions were measured and analysed. The primary and secondary relationships of the water–binder ratio, sand–binder ratio and replacement rate of fly ash to cement on the physical and mechanical properties of FHFC were studied. The failure mechanism of FHFC under uniaxial compression was discussed and a two-stage phenomenological constitutive model of FHFC was established through theoretical derivation. The results show that sand–binder ratio and water–binder ratio are the main factors affecting the physical and mechanical properties of FHFC. The stress–strain curve shows the characteristics of stages, namely, the elastic–plastic stage, the stress upswing stage, the plastic plateau stage and the failure stage. The influence of each factor on the elastic–plastic stage of the stress–strain curve shows obvious regularity, but the influence on the plastic stage is complex, and the regularity is not significant. The established two-stage phenomenological constitutive model is in good agreement with the stress–strain curve obtained from the test, and it can more accurately predict the uniaxial compression response of FHFC. The model can be used for the theoretical calculation of the bearing capacity of high-strength foam concrete structural members and even serve as an important basis for the engineering application of high-strength foam concrete. The influences of various factors on the performance of fibre-reinforced high-performance fly ash foam concrete were investigated. The uniaxial compression failure mechanism and stress–strain curve of fibre-reinforced high-performance fly ash foam concrete in different test groups were analysed. A two-stage phenomenological constitutive model suitable for fibre-reinforced high-performance fly ash foam concrete was established.

High-volume ultrafine fly ash-cement slurry mechanical properties and strength development model establishment

A Novel Strength Model for Cement Marine Clay Based on the Mechanical-Chemical Coupling Behavior

Research on Sustainable Development of Fine-Grained Material Cement Slurry

Investigation of Low-Calcium Circulating Fluidized Bed Fly Ash on the Mechanical Strength and Microstructure of Cement-Based Material

Investigation of basic properties, microscopic characteristics, and optimized ratio prediction model of ultra-high steel fiber reinforced concrete

Molecular mechanism of fly ash affecting the performance of cemented backfill material

The Influence and Application of Slag, Fly Ash, and Limestone Flour on Compressive Strength of Concrete Based on the Concrete Compressive Strength Development over Time (CCSDOT) Model

Experimental Investigation into the Proportion of Cemented Aeolian Sand-Coal Gangue-Fly Ash Backfill on Mechanical and Rheological Properties

Experimental Investigation and Numerical Model for Chloride Diffusivity of Long-Age Fly Ash Cement Slurry

Mechanical properties and constitutive model of fibre-reinforced high-performance class-F fly ash foam concrete

Modeling of Effect of Fly Ash Amount on Microstructure and Chloride Diffusivity of Blended Fly Ash-Cement Systems

The Relationship of Compressive Strength and Chemically Bound Water Content of High-Volume Fly Ash-Cement Mortar

Mechanical model and strength development evolution of high content fly ash–cement grouting material

Research on Cement Slurry Using Silica Fume Instead of Fly Ash

Impact of particle size of fly ash on the early compressive strength of concrete: Experimental investigation and modelling

Coupled effects of fly ash and calcium formate on strength development of cemented tailings backfill

Influence of fly ash on mechanical properties and hydration of calcium sulfoaluminate-activated supersulfated cement

Resource Utilization of Ultrasonic Carbonated MSWI Fly Ash As Cement Aggregates: Compressive Strength, Heavy Metal Immobilization, and Environmental-Economic Analysis

Mechanical Properties, Curing Mechanism, and Microscopic Experimental Study of Polypropylene Fiber Coordinated Fly Ash Modified Cement–Silty Soil

Multi-Response Optimization of Ultrafine Cement-Based Slurry Using the Taguchi-Grey Relational Analysis Method

Effect of Cementitious Material Composition on the Performance of Low-Carbon Foamed Lightweight Soil