Abstract:Fibre-reinforced high-performance fly ash foam concrete (FHFC) has broad engineering application prospects owing to its lightweight and high-strength, energy-saving, heat preservation and environmental protection characteristics. Its mechanical properties and constitutive models can serve as an important basis for engineering structural design, numerical analysis and structural reliability monitoring. Aimed at exploring the influence of different factors on the physical and mechanical properties of FHFC and its stress–strain constitutive relationship, the dry density, cube compressive strength, splitting tensile strength and axial compressive strength of 27 groups of FHFC with different mixture proportions were measured and analysed. The primary and secondary relationships of the water–binder ratio, sand–binder ratio and replacement rate of fly ash to cement on the physical and mechanical properties of FHFC were studied. The failure mechanism of FHFC under uniaxial compression was discussed and a two-stage phenomenological constitutive model of FHFC was established through theoretical derivation. The results show that sand–binder ratio and water–binder ratio are the main factors affecting the physical and mechanical properties of FHFC. The stress–strain curve shows the characteristics of stages, namely, the elastic–plastic stage, the stress upswing stage, the plastic plateau stage and the failure stage. The influence of each factor on the elastic–plastic stage of the stress–strain curve shows obvious regularity, but the influence on the plastic stage is complex, and the regularity is not significant. The established two-stage phenomenological constitutive model is in good agreement with the stress–strain curve obtained from the test, and it can more accurately predict the uniaxial compression response of FHFC. The model can be used for the theoretical calculation of the bearing capacity of high-strength foam concrete structural members and even serve as an important basis for the engineering application of high-strength foam concrete. The influences of various factors on the performance of fibre-reinforced high-performance fly ash foam concrete were investigated. The uniaxial compression failure mechanism and stress–strain curve of fibre-reinforced high-performance fly ash foam concrete in different test groups were analysed. A two-stage phenomenological constitutive model suitable for fibre-reinforced high-performance fly ash foam concrete was established.

Investigation of basic properties, microscopic characteristics, and optimized ratio prediction model of ultra-high steel fiber reinforced concrete

Mechanical Properties of SFRC: Database Construction and Model Prediction

High-flowable and High-Performance Steel Fiber Reinforced Concrete Adapted by Fly Ash and Silica Fume

Utilization of Waste Foundry Sand and Fly Ash in the Production of Steel Fibre Reinforced Concrete

Mechanical Behaviour and Environmental Benefit of Eco-Friendly Steel Fibre-Reinforced Dry UHPC Incorporating High-Volume Fly Ash and Crumb Rubber

Development and Properties of Cost-Effective Self-Sensing Ultra-High Performance Fiber-Reinforced Concrete (uhpfrc) Incorporating Steel Slags

Compressive Strength Of Ultra-High Strength Fiber-Reinforced Cementitious Composites (Uhsfrcc) Containing Silica Fume

Influence of Steel Fiber on Compressive Properties of Ultra-High Performance Fiber-Reinforced Concrete

Strength Design of Ultra-High-Performance Fiber-Reinforced Cementitious Composites Using Local Ecological Admixture

Sustainable development of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC): Towards to an optimized concrete matrix and efficient fibre application

Compressive Strength and Splitting Tensile Strength of Steel Fiber Reinforced Ultra High Strength Concrete (SFRC)

Mechanical properties, flexural behavior, and chloride permeability of high-performance steel fiber-reinforced concrete (SFRC) modified with rice husk ash and micro-silica

Mechanical performance and numerical simulation of high-performance steel fiber reinforced concrete

Effect of air-cooled blast furnace slag aggregate on mechanical properties of ultra-high-performance concrete

Experimental investigation on static and dynamic mechanical properties of steel fiber reinforced ultra-high-strength concretes

A comprehensive performance evaluation and optimization of steel/carbon fiber-reinforced eco-efficient concrete (FREC) utilizing multi-mechanical indicators

Effect of different steel fiber types on mechanical properties of ultra-high performance concrete

Study on the modification effect and mechanism of composite solid waste and steel fiber on the mechanical properties of concrete

Experimental study on flexural performance of ultra-high-performance concrete with recycled aggregate co-modified by nano-silica and steel fiber

Mechanical Properties and Axial Compression Deformation Property of Steel Fiber Reinforced Self-Compacting Concrete Containing High Level Fly Ash

Mechanical properties and constitutive model of fibre-reinforced high-performance class-F fly ash foam concrete