Abstract:Abstract Background: Recording of electrical activity of neurons is indispensable for decoding the information in the brain. The amplitude of signals recorded by electrodes is small, and it must be amplified to the level that can be digitalized by the analog-to-digital convert (ADC). A micro-power low-noise neural recording amplifier is indispensable for implant hippocampal cognitive prosthesis. When the process turns into deep submicron, the gate leakage current of the metal oxide semiconductor (MOS) transistor becomes larger and mismatch between devices becomes worsen. It is necessary to keep the neural amplifier robust in all process corners. Methods: The proposed circuit is a two-stage amplifier which can achieve a good trade-off between power consumption and noise. Four second-stage amplifiers share a common reference amplifier to reduce area and power consumption. A pseudo-resistor with high resistance is utilized to realize a very-low frequency high pass corner without external components. In order to minimize process variation, a bulk-compensated (BC) technique is adopted to maintain adequate tolerance in all corner case. Results: The 4-channel neural amplifier is designed and fabricated in a 40 nm standard complementary metal oxide semiconductor (CMOS) process. It achieves a mid-band gain of 54 dB, a bandwidth of 70 Hz to 7.7 kHz, a total input-referred noise of 3.2 μVrms , and a Noise Efficiency Factor (NEF) of 3.3 while consuming 4.68 µW from the 1.1 V supply. The core area of one channel is only 0.032 mm 2 . Conclusion: A 4-channel integrated neural recording amplifier chip with bias-compensated circuits is presented in this paper. Extensive simulations insure that the design is “center”. The chip layout is verified using design rules check (DRC) and layout versus schematic (LVS) design check with the help of verification tools. Test results shows that it is less sensitive to process variation and consumes less power compared with amplifier without bulk-compensated circuit. This makes the design robust and uniquely appropriate for low-power implant application.

A High Input Impedance Low Noise Integrated Front-End Amplifier for Neural Monitoring

Low Noise CMOS Front-End Amplifier Used in Detection of Extracellular Neural Signals (ENG)

System Design of a Low Noise, Low Offset Instrumentation Amplifier with Chopper Stabilization

A Robust 4-channel Micro-power Low-noise Neural Recording Amplifier for Hippocampal Cognitive Prosthesis

A 0.061-Mm² 1–11-Ghz Noise-Canceling Low-Noise Amplifier Employing Active Feedforward with Simultaneous Current and Noise Reduction

Noise Efficient Integrated Amplifier Designs for Biomedical Applications

A 2.1/5.2-NEF/PEF Capacitively Coupled Instrumentation Amplifier with Fast - Settling for Biosensor

A Low Power Low Noise Front End Amplifier for ECG Monitoring

A low-noise CMOS front-end amplifier based on auto correction feedback for biomedical systems

Power-to-Noise Optimization in the Design of Neural Recording Amplifier Based on Current Scaling, Source Degeneration Resistor, and Current Reuse

Ultra-High Input Impedance, Low Noise Integrated Amplifier for Noncontact Biopotential Sensing

Design of Ultra-Low Power Biopotential Amplifiers for Biosignal Acquisition Applications

A Low Power Low Noise Analog Front End for Portable Healthcare System

Tunnel FET-based Ultra-Low Power, Low-Noise Amplifier Design for Bio-Signal Acquisition

Design Of A Low-Noise, High Power Efficiency Neural Recording Front-End With An Integrated Real-Time Compressed Sensing Unit

Design of A Low Noise Neural Recording Amplifier for Closed-loop Neuromodulation Applications

A 77 Nw Bioamplifier with a Tunable Bandwidth for Neural Recording Systems

An Adaptive Averaging Low Noise Front-End for Central and Peripheral Nerve Recording

Design of Readout Circuit Based on Probe Neural Biosensor

A Low-Noise Low-Power Amplifier for Electroencephalogram Recording