Abstract:Abstract Background: Recording of electrical activity of neurons is indispensable for decoding the information in the brain. The amplitude of signals recorded by electrodes is small, and it must be amplified to the level that can be digitalized by the analog-to-digital convert (ADC). A micro-power low-noise neural recording amplifier is indispensable for implant hippocampal cognitive prosthesis. When the process turns into deep submicron, the gate leakage current of the metal oxide semiconductor (MOS) transistor becomes larger and mismatch between devices becomes worsen. It is necessary to keep the neural amplifier robust in all process corners. Methods: The proposed circuit is a two-stage amplifier which can achieve a good trade-off between power consumption and noise. Four second-stage amplifiers share a common reference amplifier to reduce area and power consumption. A pseudo-resistor with high resistance is utilized to realize a very-low frequency high pass corner without external components. In order to minimize process variation, a bulk-compensated (BC) technique is adopted to maintain adequate tolerance in all corner case. Results: The 4-channel neural amplifier is designed and fabricated in a 40 nm standard complementary metal oxide semiconductor (CMOS) process. It achieves a mid-band gain of 54 dB, a bandwidth of 70 Hz to 7.7 kHz, a total input-referred noise of 3.2 μVrms , and a Noise Efficiency Factor (NEF) of 3.3 while consuming 4.68 µW from the 1.1 V supply. The core area of one channel is only 0.032 mm 2 . Conclusion: A 4-channel integrated neural recording amplifier chip with bias-compensated circuits is presented in this paper. Extensive simulations insure that the design is “center”. The chip layout is verified using design rules check (DRC) and layout versus schematic (LVS) design check with the help of verification tools. Test results shows that it is less sensitive to process variation and consumes less power compared with amplifier without bulk-compensated circuit. This makes the design robust and uniquely appropriate for low-power implant application.

Low Noise CMOS Front-End Amplifier Used in Detection of Extracellular Neural Signals (ENG)

System Design of a Low Noise, Low Offset Instrumentation Amplifier with Chopper Stabilization

Design of Readout Circuit Based on Probe Neural Biosensor

A Robust 4-channel Micro-power Low-noise Neural Recording Amplifier for Hippocampal Cognitive Prosthesis

A 2.1/5.2-NEF/PEF Capacitively Coupled Instrumentation Amplifier with Fast - Settling for Biosensor

A Low-Noise Chopper Amplifier Designed for Multi-Channel Neural Signal Acquisition

A low-noise CMOS front-end amplifier based on auto correction feedback for biomedical systems

Design of a 3.24μW, 39nV/√Hz chopper amplifier with 5.5Hz noise corner frequency for invasive neural signal acquisition

Design of A Low Noise Neural Recording Amplifier for Closed-loop Neuromodulation Applications

A High Input Impedance Low Noise Integrated Front-End Amplifier for Neural Monitoring

Design Of A 3.24 Mu W, 39nv/Root Hz Chopper Amplifier With 5.5hz Noise Corner Frequency For Invasive Neural Signal Acquisition

A low-power CMOS neural amplifier with amplitude measurements for spike sorting

32-Channel Full Customized Cmos Biosensor Chip For Extracellular Neural Signal Recording

A Low Power Low Noise Analog Front End for Portable Healthcare System

Design Of A Low-Noise, High Power Efficiency Neural Recording Front-End With An Integrated Real-Time Compressed Sensing Unit

A 0.8V Chopper Amplifier with 600mvpp Tolerance to Power-Line Interference for Neural Signal Acquisition

Low-noise CMOS Charge-Sensitive Preamplifier

Design of a Low-Noise Multi-Range Broadband Front-End Amplifier for MEMS Electric Field Sensor

A Design of EES Analog Pre-processing Circuit

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A Low Power Low Noise Front End Amplifier for ECG Monitoring