Abstract:Abstract Nickel-base superalloys (NBSAs) are extensively utilized as the design materials to develop turbine blades in gas turbines due to their excellent high-temperature properties. Gas turbine blades are exposed to extreme loading histories that combine high mechanical and thermal stresses. Both directionally solidified (DS) and single crystal NBSAs are used throughout the industry because of their superior tensile and creep strength, excellent low cycle fatigue (LCF), high cycle fatigue (HCF), and thermomechanical fatigue (TMF) capabilities. Directional solidification techniques facilitated the solidification structure of the materials to be composed of columnar grains in parallel to the <001> direction. Due to grains being the sites of failure initiation the elimination of grain boundaries compared to polycrystals and the alignment of grain boundaries in the normal to stress axis increases the strength of the material at high temperatures. To develop components with superior service capabilities while reducing the development cost, simulating the material’s performance at various loading conditions is extremely advantageous. To support the mechanical design process, a framework consisting of theoretical mechanics, numerical simulations, and experimental analysis is required. The absence of grain boundaries transverse to the loading direction and crystallographic special orientation cause the material to exhibit anisotropic behavior. A framework that can simulate the physical attributes of the material microstructure is crucial in developing an accurate constitutive model. The plastic flow acting on the crystallographic slip planes essentially controls the plastic deformation of the material. Crystal Visco-Plasticity (CVP) theory integrates this phenomenon to describe the effects of plasticity more accurately. CVP constitutive models can capture the orientation, temperature, and rate dependence of these materials under a variety of conditions. The CVP model is initially developed for SX material and then extended to DS material to account for the columnar grain structure. The formulation consists of a flow rule combined with an internal state variable to describe the shearing rate for each slip system. The model presented includes the inelastic mechanisms of kinematic and isotropic hardening, orientation, and temperature dependence. The crystallographic slip is accounted for by including the required octahedral, cubic, and cross slip systems. The CVP model is implemented through a general-purpose finite element analysis software (i.e., ANSYS) as a User-Defined Material (USERMAT). Uniaxial experiments were conducted in key orientations to evaluate the degree of elastic and inelastic anisotropy. The temperature-dependent modeling parameter is developed to perform non-isothermal simulations. A numerical optimization scheme is utilized to develop the modeling constant to improve the calibration of the model. The CVP model can simulate material behavior for DS and SX NBSAs for monotonic and cyclic loading for a range of material orientations and temperatures.

The Influence of Crystal Orientation on the Elastic Stresses of a Single Crystal Nickel-Based Turbine Blade

Effect of crystal orientation on elastic stresses and vibration characteristics of nickel-based single crystal turbine blade

Effect of Crystal Orientation on Fatigue Failure of Single Crystal Nickel Base Turbine Blade Superalloys

Primary Crystal Orientation of the Thin-Walled Area of Single-Crystalline Turbine Blade Airfoils

The Influence of the Cooling Bores on Crystal Orientation and Lattice Parameter in Single-Crystalline Cored Turbine Blades

Influence of Deviation and Randomness of Crystallographic Orientations on the Strength and Life of Nickel-Base Single Crystal Superalloy Turbine Blades

A systematical investigation on the impact of coupling crystal orientations on vibration characteristics of a single crystal superalloy cooling turbine blade

Determination of Crystal Orientation by Ω-Scan Method in Nickel-Based Single-Crystal Turbine Blades

An Arc-tenon Attachment for Nickel-based Single Crystal Turbine Blade with Improved High-Temperature Fretting Fatigue Performance

Effect of Blade Geometry on γ' Lattice Parameter and Primary Orientation of SX Cored Turbine Blades (II)

Crystal plasticity analysis of fatigue-creep behavior at cooling holes in single crystal Nickel based gas turbine blade components

Effect of Blade Geometry on γ' Lattice Parameter and Primary Orientation of SX Cored Turbine Blades (I)

Secondary orientation effects on the low cycle fatigue behaviors of rectangular‐sectional Ni‐based single crystal superalloys at medium and high temperatures

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

A multiaxial probabilistic fatigue life prediction method for nickel‐based single crystal turbine blade considering mean stress correction

Dimensional Control of Nickel-Based Single Crystal Turbine Blade Investment Casting by Process Control Optimization

Modeling of Unidirectional Growth in a Single Crystal Turbine Blade Casting

Tensile behavior of single-crystal superalloy with different structured cooling holes

The recent progress in the design of structural strength and life assessment for aero-engine single crystal turbine blades

Crystal Visco-Plastic Model for Directionally Solidified Ni-Base Superalloys Under Monotonic and Low Cycle Fatigue

Effect of secondary orientation on the microstructures in thin-walled castings of nickel-based single-crystal superalloys