Abstract:At partial load, traditional automotive gasoline engines have high pumping losses due to the throttling of the intake charge for load control. Variable Valve Timing (VVT) and the introduction of externally cooled EGR could reduce the pumping losses but only with a very limited effect. On the other hand, in the medium to full load range, the engine cannot utilize a high compression ratio due to limitations in knocking. A variable displacement, variable compression ratio device which utilizes an asymmetric camshaft to realize the different closure times of the two intake valves is discussed in this paper. The large-scale change in the intake valve timing leads to the large-scale change in the effective cylinder volume at the intake valve closure, which realizes a variable cylinder volume and a variable effective compression ratio. The device is utilized to reduce the pumping losses and to increase the in-cylinder thermal efficiency at the same time. Engine dyno test results indicate that, in the low to medium load range, a later closure of the intake valve could reduce the effective cylinder volume, and the intake pressure could be significantly increased, and therefore pumping losses reduced. However, the reduced effective cylinder volume due to a later intake valve closure would lead to reduction in the effective compression ratio (ECR) and a drop in in-cylinder thermal efficiency. Therefore, there is a balance point between the pumping loss reduction and the drop in in-cylinder thermal efficiency. On the other side, in the medium to full load range, when avoiding knocking becomes the major controlling factor of the combustion phasing (degree of constant-volume combustion) and the effective expansion ratio (EER), too high of an effective compression ratio would lead to significant drop in the effective expansion ratio EER and also the in-cylinder thermal efficiency. Therefore, there exists a best compromise between the ECR and EER, and the best system would be one with a moderate ECR but an EER as high as possible. The quantitative equations which include both ECR and EER in the thermal efficiency calculations captured the above observations pretty well and can be utilized to optimize for the best compromise of IVC, EVO, ECR, EER and engine performances during the concept stage and/or the calibration stage of an engine.

Combustion Technology Development for a High Compression Ratio SI Engine

A Study on Combustion Characteristics of a High Compression Ratio SI Engine with High Pressure Gasoline Injection

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Optimization of Piston Bowl and Valve System in Compression Ignition Engine Fueled with Gasoline/diesel/polyoxymethylene Dimethyl Ethers for High Efficiency

Fundamental Study on Combustion Improvement by Mixture-Flow in Natural Gas-Fueled Lean-Burn SI Engines

Towards High Efficiency of Intelligent Charge Compression Ignition (ICCI) Engine by Optimizing the High-Reactivity Fuel Injection Strategies under Medium–high Loads

High Compression Ratio Active Pre-chamber Single-Cylinder Gasoline Engine with 50% Gross Indicated Thermal Efficiency

Understanding the Correlation Between Auto-Ignition, Heat Release and Knocking Characteristics Through Optical Engines with High Compression Ratio

Development and Validation of a Variable Displacement Variable Compression Ratio Miller Cycle Technology on an Automotive Gasoline Engine

Thermal efficiency improvement of super-lean burn spark ignition engine by stratified water insulation on piston top surface

Survey of Greener Ignition and Combustion Systems for Internal Combustion Engines

Improving the Efficiency of Spark-Ignition Internal Combustion Engine Using a Novel Electromagnetic Actuator and Adapting Increased Compression

Fuel Conversion Efficiency Improvements in A Highly Boosted Spark-Ignition Engine with Ultra-Expansion Cycle

Effect of the Compression Ratio on the Performance and Combustion of A Natural-Gas Direct-Injection Engine

Improving Thermal Efficiency of Internal Combustion Engines: Recent Progress and Remaining Challenges

An Experimental Study on Combustion and Emissions Characteristics in a Dual-Injection Spark-Assisted Compression Ignition Engine Fueled with PODE/gasoline

Multi-objective optimization of a compression ignition engine using on-board methanol reforming

An Experiment Study of Homogeneous Charge Compression Ignition Combustion and Emission in A Gasoline Engine

Investigations on combustion system optimization of a heavy-duty natural gas engine

Combustion and Emission Enhancement of a Spark Ignition Two-Stroke Cycle Engine Utilizing Internal and External Exhaust Gas Recirculation Approach at Low-Load Operation

Combustion Research in Internal Combustion Engines and Its Challenges