Abstract:Purpose. Bony resection is the primary step during total knee arthroplasty. The accuracy of bony resection was highly addressed because it was deemed to have a good relationship with mechanical line. Patient-specific instruments (PSI) were invented to copy the bony resection references from the preoperative surgical plan during a total knee arthroplasty (TKA); however, the accuracy still remains controversial. This study was aimed at finding out the accuracy of the bony resection during PSI-assisted TKA. Methods. Forty-two PSI-assisted TKAs (based on full-length leg CT images) were analyzed retrospectively. Resected bones of every patient were given a CT scan, and three-dimensional radiographs were reconstructed. The thickness of each bony resection was measured with the three-dimensional radiographs and recorded. The saw blade thickness (1.27 mm) was added to the measurements, and the results represented intraoperative bone resection thickness. A comparison between intraoperative bone resection thickness and preoperatively planned thickness was conducted. The differences were calculated, and the outliers were defined as >3 mm. Results. The distal femoral condyle had the most accurate bone cuts with the smallest difference (median, 1.0 mm at the distal medial femoral condyle and 0.8 mm at the distal lateral femoral condyle) and the least outliers (none at the distal medial femoral condyle and 1 (2.4%) at the distal lateral femoral condyle). The tibial plateau came in second (median difference, 0.8 mm at the medial tibial plateau and 1.4 mm at the lateral tibial plateau; outliers, none at the medial tibial plateau and 1 (2.6%) at the lateral tibial plateau). Regardless of whether the threshold was set to >2 mm (14 (17.9%) at the tibial plateau vs. 12 (14.6%) at the distal femoral condyle, p>0.05) or >3 mm (1 (1.3%) at the tibial plateau vs. 1 (1.2%) at the distal femoral condyle, p>0.05), the accuracy of tibial plateau osteotomy was similar to that of the distal femoral condyle. Osteotomy accuracy at the posterior femoral condyle and the anterior femoral condyle were the worst. Outliers were up to 6 (15.0%) at the posterior medial femoral condyle, 5 (12.2%) at the posterior lateral femoral condyle, and 6 (15.8%) at the anterior femoral condyle. The percentages of overcut and undercut tended to 50% in most parts except the lateral tibial plateau. At the lateral tibial plateau, the undercut percentage was twice that of the overcut. Conclusion. The tibial plateau and the distal femoral condyle share a similar accuracy of osteotomy with PSI. PSI have a generally good accuracy during the femur and tibia bone resection in TKA. PSI could be a kind of user-friendly tool which can simplify TKA with good accuracy. Level of Evidence. This is a Level IV case series with no comparison group.

Accuracy of manual instrumentation of tibial cutting guide in total knee arthroplasty

Angle Accuracy of Intramedullary Bone Resection Guides for Total Knee Arthroplasty

Small deviations between planned and performed bone cuts using a CT‐based robotic‐arm‐assisted total knee arthroplasty system

Surgical accuracy in high tibial osteotomy: coronal equivalence of computer navigation and gap measurement

The Bony Resection Accuracy with Patient-Specific Instruments During Total Knee Arthroplasty: A Retrospective Case Series Study

Simultaneous Evaluation of Bone Cut and Implant Placement Accuracy in Robotic-Assisted Total Knee Arthroplasty

Cutting errors in total knee replacement: assessment by computer assisted surgery

Accuracy of Bone Resection in MAKO Total Knee Robotic-Assisted Surgery

Accuracy of medial-side cutting guide compared to anterior cutting guide in distal femoral osteotomy of total knee arthroplasty

Computer-assisted navigation for the intraoperative assessment of lower limb alignment in high tibial osteotomy can avoid outliers compared with the conventional technique

Cadaveric analysis of an accelerometer-based portable navigation device for distal femoral cutting block alignment in total knee arthroplasty

High three‐dimensional accuracy of component placement and lower limb alignment using a robotic arm‐assisted system and gap‐balancing instrument in total knee arthroplasty

[Evaluation and Analysis of the Tibial Coronal Alignment after Total Knee Replacement with the Extramedullary Tibial Cutting Guided by the Tibial Tubercle and Anterior Tibial Tendon in Chinese Patients].

High in‐vivo accuracy of a novel robotic‐arm‐assisted system for total knee arthroplasty

Increased accuracy in component positioning using an image-less robotic arm system in primary total knee arthroplasty: a retrospective study

Proven accuracy for a new dynamic gap measurement in navigated TKA

Advantages of patient-specific cutting guides with disposable instrumentation in total knee arthroplasty: a case control study

Accuracy and outcome of a handheld accelerometer-based navigation device compared to conventional alignment method in total knee arthroplasty in a Chinese population

Influence of lower limb rotation in navigated alignment analysis: implications for high tibial osteotomies

Accuracy of a New Robotically Assisted Technique for Total Knee Arthroplasty: A Cadaveric Study

Computer-aided planning with exact implementation into surgical technique in TKA is as accurate as intraoperative navigation.