Abstract:Abstract Two high rate acid gas injection wells were drilled in the LaBarge area of Wyoming. These wells were designed for injection of up to 65 million scf/day of a mixture of 65% H2S and 35% CO2. The primary engineering challenges in well design, casing selection, and cementing of the injection strings, along with the related operational challenges for both wells are discussed. Key drivers influencing zonal isolation, salt zone loading, casing and centralizer selection are presented. Casing selection was influenced by corrosive gas composition, high injection rates, and the potential for salt zone loading. The use of CRA tubulars, heavy wall casing for the salt loading, handling requirements, and centralizer selection are discussed. The primary driver in cement design was resistance to CO2, as past work has shown little H2S interaction with cement under these well conditions. A discussion of the development of a high alumina cement system with low fluid loss to address CO2 resistance and long liner length is coupled with the quality control steps taken from time of manufacture of the specialty cement to final placement in the well. Also described is the development of an alternate Portland cement system containing a reduced concentration of Portland cement by the use of sized particles to dilute the cement and reduce total system permeability. The unique engineering solutions resulted in operational challenges with casing running, cementing materials and equipment. A description of the location problems and the steps taken to resolve the issues are included. Introduction The acid gas injection wells were drilled as part of an overall gas plant de-bottlenecking. Plant throughput capacity was being increased by converting the plant to acid gas disposal by injection. The anticipated waste gas stream was 65% H2S and 35% CO2. Design volume for the wells was based upon the capacity of the plant plus adequate backup. The maximum planned plant waste capacity was 100 million standard cubic feet per day (MMscf/D), with the initial target waste volume planned at 65 MMscf/D per well. The corrosive gas stream required the use of specialty materials which complicated casing selection, centralizer selection and handling on location. Casing design was further challenged by the potential presence of a salt formation above the planned injection intervals. Unique cementing solutions are required in a CO2 environment. The gas converts calcium silicates in Portland cement to calcium carbonate, causing the cement to have an increased permeability and the system would be soluble in acid.1–5 CO2 flood projects typically require routine acidizing to remove scale caused by water in the gas stream. The acid could dissolve the converted cement sheath, and ultimately cause loss of containment in the annulus. The subject wells are not part of a CO2 flood, nor does the gas stream contain water, but CO2 resistance was considered integral to the design. Formation Considerations The primary zone for injection is the Madison formation (Mississippian system in the Paleozoic). The Madison is a massive carbonate composed of anhydrite and dolomite sequences within a limestone structure. This is the same formation from which the gas is produced but located far down dip. Injection is expected to be primarily into the dolomites where secondary permeability has been enhanced by the dolomitization process. Some injection would also be possible into the naturally fractured and vuggy limestones. The well designs would allow injection into all regulatory permitted intervals. Overlying and sealing the potential injection intervals is the Thaynes formation (Middle Triassic in the Mesozoic). In the producing field, the Thaynes contains thick layers of movable salt, where temperature and overburden are adequate to allow the formation to flow. In the producing field, production casing has collapsed across the salt.

Centrifugal Compressor Design Challenges for CO2 and Other Acid Gas Injection Services

Computational Analysis of the Performance Characteristics of a Supercritical CO2 Centrifugal Compressor

Implications of Phase Change on the Aerodynamics of Centrifugal Compressors for Supercritical Carbon Dioxide Applications

Aerodynamic Optimization Design of a 150 kW High Performance Supercritical Carbon Dioxide Centrifugal Compressor without a High Speed Requirement

Instability Phenomena in Centrifugal Compressors and Strategies to Extend the Operating Range: A Review

Design and analysis of centrifugal compressor in carbon dioxide heat pump system

Challenges for Developing and Marketing a Brayton-Cycle Based Power Genset Gas-Turbine Using Supercritical CO2 and a Compressor Design for Simple Recuperated Cycle

The Design, Selection, and Application of Oil-Injected Screw Compressors for Fuel Gas Service

EFFECT OF COMPRESSOR INLET CONDITION ON SUPERCRITICAL CARBON DIOXIDE COMPRESSOR PERFORMANCE

Design and Closed Loop Testing of High-Pressure Centrifugal Gas Compressors for the Suppression of Subsynchronous Vibration

Design of a Centrifugal Compressor with Low Solidity Vaned Diffuser (LSVD) for Large-Scale Compressed Air Energy Storage (CAES)

An Investigation of Condensation Effects in Supercritical Carbon Dioxide Compressors

Direction for High-Performance Supercritical CO2 Centrifugal Compressor Design for Dry Cooled Supercritical CO2 Brayton Cycle

Meeting the Challenges in Design and Execution of Two High Rate Acid Gas Injection Wells

Modal analysis and structural optimization of integrated bladed disks and centrifugal compressor impellers

Aerodynamic limits air injection for heavy-duty gas turbine: Compressor aerodynamic limits for power augmentation and ramp-up capabilities

Design of a Partial Discharge Shrouded Impeller for the Centrifugal Compressor of Supercritical Carbon Dioxide Power Cycles

Concepts for Hybrid Electric Motor-Gas Turbine Driven Compressors

Transcritical / Supercritical CO2 Recompression Brayton Cycle Using a Novel Rotary Liquid Piston Compressor

Compression Technology Selection for Downhole Application in Gas Wells

Impact of CO2 Specifications on Design and Operation Challenges of CO2 Transport and Storage Systems in CCUS