Abstract:Wear due to sliding is an inevitable problem in many engineering applications. Protective surface coating is usually used to mitigate this problem. The development in this field is continuous and consistent. There are many types of coatings according to their compositions and the deposition methods. One of the coatings with the most promising properties, such as the hardness, is the Diamond-Like Carbon (DLC) coating. The tribological properties of this coating generated by Plasma-Assisted Chemical Vapor Deposition (PACVD) and applied on bearing steel 52100 ASTM are not available. In this study, the wear resistance of the DLC coating applied to bearing steel 52100 ASTM, was evaluated. The coating method employed was PACVD, which is regarded as one of the most distinctive coating techniques due to the unique tribological properties imparted to the coating. The pin-on-disc tribometer was used to examine the coefficient of friction and mass losses for samples of (steel disc against steel ball) and (DLC coated disc against DLC coated ball) under constant sliding velocity and constant sliding distance with four different loads (2, 5, 10 and 20 N) that results in maximum contact pressure below and higher than the maximum shear stress of the bearing steel. The wear coefficient was calculated using Archard's equation based on the experimental results. It was found that the DLC coating may result in significant reduction, reaching 93.5%, in weight loss and 83% in COF at low contact pressure (less than the maximum shear stress). However, at high contact pressure (equals to or higher than the maximum shear stress) the weight loss and the COF for the DLC coating are higher than those of the bearing steel. This behavior indicates that the DLC coated pair may not be suitable at high loads. The wear coefficient is calculated for each testing condition and it is found to be affected by the applied load. The average wear coefficient for the DLC coating is provided which can be used with the Archared wear model to predict the wear rate within the range of the parameters used in this study.

Evaluating the Mechanical and Tribological Properties of DLC Nanocoated Aluminium 5051 Using RF Sputtering

Tribological Properties of Diamond-Like Carbon Films Deposited by Vacuum Arc

Diamond-Like Carbon Thin Films Deposited On Ti6al4v Alloy Surface By Plasma Gun At Atmospheric Pressure

The effect of diamond like carbon coating on the wear resistance at dry sliding conditions

Comprehensive structural, nanomechanical and tribological evaluation of silver doped DLC thin film coating with chromium interlayer (Ag-DLC/Cr) for biomedical application

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

Structural Characters and Tribological Properties of Diamondlike Carbon Films

Exploring long-run reciprocating Wear of diamond-like carbon coatings: microstructural, morphological and tribological evolution

A study of the wear mechanism of diamond-like carbon films

Diamond-like Carbon Film Synthesized by Ion Beam Assisted Deposition and Its Tribological Properties

Tribological study of lubricious DLC biocompatible coatings

Studies of Diamond-Like Carbon Films Prepared by Ion Beam-Assisted Deposition

Improving Tribological Performance of Piston Ring Steel Substrates by DLC/Nano-crystalline Diamond Coating

The Effect of DLC Surface Coatings on Microabrasive Wear of Ti-22Nb-6Zr Obtained by Powder Metallurgy

Tribological Properties of Graded Diamond-Like Carbon Films on Ti Ion-Implanted Aluminum Substrate

Microstructure, mechanical and tribological properties of multilayer Ti-DLC thick films on Al alloys by filtered cathodic vacuum arc technology

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

Preparation, Characterization and Tribological Properties of Diamond-Like Carbon Film on AZ31 Magnesium Alloy

Mechanical and Tribological Properties of Diamond-Like Carbon Films Deposited by Electron Cyclotron Resonance Microwave Plasma Chemical Vapor Deposition

Characterisation of Ultra-Thin DLC Coatings by SEM/EDX, AFM and Electrochemical Techniques

Electrodeposition, microstructure, friction and electrochemical behavior of diamond-like carbon (DLC) films with Ni/Cu interlayer