Abstract:Structural Health Monitoring, Ahead of Print. Welding is a commonly used method for joining two or more parts together in steel construction. Various defects in weld regions such as cracks, pores, and slag inclusion can be present from the beginning, generated during the welding process, or can be developed while in service. Such defects are the weak spots that degrade the structure's quality and can lead to structural failures. Therefore, early detection of these defects in welded joints, before visible cracks appear, is very important. Using appropriate ultrasonic non-destructive testing and evaluation (NDT&E) techniques, one can detect these defects and take remedial actions to prevent catastrophic structural failures. Guided acoustic wave-based techniques have been proven to be effective for damage detection in steel pipes and rods. Several studies have previously attempted to detect damage in steel tubes using guided ultrasonic waves. Unlike earlier attempts which mostly focused on conventional linear ultrasonic techniques, a relatively new nonlinear ultrasonic technique called sideband peak count-index (SPC-I) is carried out in this research. For this investigation, cast steel components and round hollow structural sections are welded together, and a four-point bending test is conducted under fatigue loading. The welded joints are continuously monitored in real time using strain gages and lead zirconate titanate (PZT) transducers. The PZT transducers are used to generate and receive guided acoustic waves. The signal is propagated through the specimen in a single-sided transmission mode setup. The strain gage readings and the nonlinear ultrasonic parameter, the SPC-I values, are monitored simultaneously. The results obtained from the nonlinear ultrasonic NDT&E measurements are compared with the data obtained from the strain gages to determine the robustness and reliability of the SPC-I technique for monitoring welded joints. This investigation also shows the potential effectiveness of the nonlinear ultrasonic parameter SPC-I for early detection of weld failure.

Nondestructive Evaluation of Electroplating-Induced Hydrogen Embrittlement in Cadmium-Coated High-Strength Steel Using Ultrasonic Surface Waves

Depth-Sensing Indentation-Based Studies of Surface Mechanical Behavior and Fatigue Damage Evolution of an Austenitic Stainless Steel Subjected to Cyclic Straining

Feasibility of using ultrasonic-based prediction for hydrogen embrittlement susceptibility of high-strength heat-resistant steel 2.25Cr-1Mo-0.25V

An Experimental Assessment Using Acoustic Emission Sensors to Effectively Detect Surface Deterioration on Steel Plates

A Study of the Automated Eddy Current Detection of Cracks in Steel Plates

The use of acousto-ultrasonics to determine the quality of the brazing of carbide-tipped cutting tools

Early detection of steel tube welded joint failure using SPC-I nonlinear ultrasonic technique

A Thickness Nondestructive Evaluation Strategy for Coating Located in Truncated Conical Steel Shells of Various Sizes Based on Eddy Current Testing Technology

Health Monitoring of Stiffened Metallic Plates Using Nonlinear Wave Interaction and Embedded PZT Transducers

Optimized Analytical Approach for the Detection of Process-Induced Defects Using Acoustic Emission During Directed Energy Deposition Process

Hydrogen Permeation Study on Zinc-Nickel Coated Ultra-High Strength Martensitic Steels

Nondestructive Inspection of Directed Energy Deposited Components Using Scanning Acoustic Microscopy with Metalworking Fluids

Experimental and Molecular Dynamics Simulation-Based Investigations on Hydrogen Embrittlement Behavior of Chromium Electroplated 4340 Steel

Metal defects sizing and detection under thick coating using microwave NDT

Evaluation of Hydrogen Embrittlement Susceptibility of Underwater Laser Direct Metal Deposited 316L Stainless Steel

Simultaneous Evaluation of Residual Stress and Plastic Deformation in Ferromagnetic Steel by Using an Integrated NDE Method

The Application of Ultrasonics to Electroplating with a View to Reducing Hydrogen Embrittlement

Subsurface Defect Evaluation of Selective-Laser-Melted Inconel 738LC Alloy Using Eddy Current Testing for Additive/Subtractive Hybrid Manufacturing

Early corrosion detection in structural carbon steels using electromagnetic sensors

Pulsed Eddy Current Nondestructive Testing for Defect Evaluation and Imaging of Automotive Lightweight Alloy Materials

The application of electroplating for prevention of hydrogen embrittlement in AISI 4140 steel