Abstract:With the rapid development of the third-generation semiconductor materials, an appropriate high-temperature-resistant die attach material has become one of the bottlenecks to fully exploit the excellent properties of the third-generation semiconductor power devices. At the same time, a low-bonding temperature is always the pursuit goal of packaging engineers to reduce the thermal residual stress in electronic devices. In this paper, a low-temperature bonding method was proposed to address the above-mentioned issue based on In infiltrating the nanoporous Cu. In, as a low melting point metal, can significantly reduce the bonding temperature, and the nanoporous Cu structure can provide a very large specific surface area, which greatly increases the consumption rate of In. Furthermore, the formed Cu-In IMCs with high-remelting temperature can withstand the high operating temperature. The microstructures of the bondlines before and after bonding were studied in detail. The results show that the bondline can completely consume the low melting point In, within 10 min at 165 °C under a pressure of 0.75 MPa. When the bonding temperature was further increased to 310 °C, the bondline was composed of η-Cu2In and δ-Cu7In3 phases, whose melting points were more than 600 °C. The average electrical resistivity was determined to be 5.53 ± 0.65 μΩ cm, and the thermal conductivities were 144.33 W m−1 K−1, 139.24 W m−1 K−1 and 129.79 W m−1 K−1 at 30 °C, 150 °C and 300 °C, respectively. The average shear strength were 19.09 ± 3.4 MPa, 20.47 ± 4.6 MPa and 30.73 ± 5.2 MPa at 30 °C, 250 °C, 310 °C, respectively. These results indicate that the nanoporous Cu infiltrated with In could meet the requirements of electrical, thermal conduction, and mechanical support as a die attachment for high-power devices.

Cu–Cu Bond Quality Enhancement Through the Inclusion of a Hermetic Seal for 3-D IC

Cu-Based Thermocompression Bonding and Cu/Dielectric Hybrid Bonding for Three-Dimensional Integrated Circuits (3D ICs) Application

Development of low temperature Cu Cu bonding and hybrid bonding for three-dimensional integrated circuits (3D IC)

Solid-State-Diffusion Bonding for Wafer-Level Fine-Pitch Cu/Sn/Cu Interconnect in 3-D Integration

Interfacial Characterization of Low-Temperature Cu-to-Cu Direct Bonding with Chemical Mechanical Planarized Nanotwinned Cu Films

A low-temperature bonding method for high power device packaging based on In-infiltrated nanoporous Cu

Low-Temperature Cu–Cu Direct Bonding Using Pillar–Concave Structure in Advanced 3-D Heterogeneous Integration

Effects of surface treatment on the bonding quality of wafer-level Cu-to-Cu thermo-compression bonding for 3D integration

Low temperature solid-state-diffusion bonding for fine-pitch Cu/Sn/Cu interconnect

Enhanced Cu-Cu bonding for ultrahigh-density interconnection: Co passivation bonding with non-oxidation interfaces

Low Temperature Fine-Pitch Wafer-Level Cu-Cu Bonding Using Nanoparticles Fabricated by PVD

Wafer-Level Hermetic Package by Low-Temperature Cu/Sn TLP Bonding with Optimized Sn Thickness

Eliminating Cu–Cu Bonding Interfaces Using Electroplated Copper and (111)-Oriented Nanotwinned Copper

An Insertion-Based Mechanical Interlock Cu-Sn Bonding Structure for Three-Dimensional Integration

Enhanced Copper Bonding Interfaces by Quenching to Form Wrinkled Surfaces

Low Temperature Cu/SiO2 Hybrid Bonding with Protruding Copper Pads

Study on copper-to-copper bonding of three-dimensional integrated circuits using the quasicontinuum method

Effects of Bonding Parameters on the Reliability of Fine-Pitch Cu/Ni/SnAg Micro-Bump Chip-to-Chip Interconnection for Three-Dimensional Chip Stacking

Rapid formation, grain refinement and shear property of high-temperature-stable full IMC joints

Low-temperature Cu Cu Direct Bonding with Ultra-Large Grains Using Highly (110)-Oriented Nanotwinned Copper

A Cu-Sn/BCB Hybrid Bonding with Embedded Bump Structure