Abstract:The Savonius rotor has been attracting more and more attention in recent years owing to its appealing features, such as simplicity of the fabrication, cost-effectiveness in low wind speed areas and low noise levels. It can be used for lighting, ventilation, hydropower generation and irrigation. As a traditional single-stage two-blade Savonius rotor has two defects, researchers proposed the multi-stage two-blade Savonius rotor to overcome them. However, most of the previous studies on the multi-stage Savonius rotors focused on the comparison between one- and two-stage rotors or the effect of the aspect ratios. This paper is different from previous researches and focuses on the comparison between two-stage rotors through the wind tunnel test. It also studies the effect of the gap ratio (GR) and phase shift angle (PSA) on the performance of the two-stage rotors at different wind speeds. Results showed that the negative azimuth angle range was narrowed and the torque coefficient (CT) values were improved as GR and PSA increased. Hence, the two-stage rotor with larger GR and PSA can overcome the two defects of the single-stage rotor. In terms of the power coefficient (CP), the optimized performance was determined by the GRs, PSAs, and wind speeds. When the wind speed increased, the difference among CP curves of one tested rotor was reduced. Generally speaking, the rotors with GR = 1/6 exhibited the optimized performance compared with those with other GRs when the PSA = 0° and PSA = 45°. While keeping the PSA = 90°, the rotor with GR = 0 had a superior performance to the others when PSA = 90° at wind speed of 4 m/s. The rotor with GR = 1/3 gave the highest CP value of 0.303 in the vicinity of the tip speed ratio 0.9 at wind speed of 6 m/s. And the rotor with GR = 1/6 attained the best CP when the wind speeds were 8 m/s and 10 m/s.

Performance Comparison of Large-scale Design-optimised Non-overlap and Overlap Winding Wound Rotor Synchronous Generators

Performance Comparison of Large-Scale Design-Optimized Non-Overlap and Overlap Winding Wound Rotor Synchronous Generators

Comparison of Dual 3-Phase Modular Permanent Magnet Machines with Overlapping/Non-overlapping Windings and Redundancy

Comparison of Optimal Design and Performance of PM Machines Having Non-Overlapping Windings and Different Rotor Topologies

Enhanced Ventilation and Thermal Performance by Skewed Through Holes on Rotor Yoke in Forced Air-Cooled Permanent Magnet Wind Generators

Comparison of Modular Dual 3-phase PM Machines with Overlapping/Non-overlapping Windings

Comparative Study of Modular Dual 3-phase Permanent Magnet Machines with Overlapping/Non-overlapping Windings

Experimental Study of Two-Stage Savonius Rotors with Different Gap Ratios and Phase Shift Angles

Design and Comparison of Segmented Armature Windings for Superconducting Wind Turbine Generators with Multiple Converters

Comparison of Electromagnetic Performance of Superconducting Permanent Magnet Wind Power Generator with Different Topologies

Design of a Dual-Stator Superconducting Permanent Magnet Wind Power Generator with Different Rotor Configuration

Electromagnetic Design And Optimization Of Dual-Stator Brushless Doubly-Fed Wind Power Generator With Cage-Barrier Rotor

Design Aspects for Permanent Magnet Superconducting Wind Power Generators

Comparative Analysis of Coreless Axial Flux Permanent Magnet Synchronous Generator for Wind Power Generation

Electromagnetic design and performance analysis of large-scale offshore wind generators with modular fractional-slot concentrated winding

Optimum Design of an Extended Range Generator for EVs Based on Taguchi Method

Design of 20 MW direct‐drive permanent magnet synchronous generators for wind turbines based on constrained many‐objective optimization

Optimization Study of Poles-slots Combination of Large Capacity Offshore HTS Wind Generator Based on Ansys Maxwell

Study of Direct-Drive Permanent-Magnet Synchronous Generators with Solid Rotor Back Iron and Different Windings

Multiobjective Design Optimization of a Double-Sided Flux Switching Permanent Magnet Generator for Counter-Rotating Wind Turbine Applications

A Two-Stage Multi-Objective Design Optimization Model for a 6 MW Direct-Drive Permanent Magnet Synchronous Generator