Abstract:Additive manufacturing (AM) introduces unique grain feature and anisotropy in metals, as well as relatively poor surface quality, so the knowledge about the formation of post-machining-induced surface integrity needs to be extended. This study aims to understand the machining phenomena in orthogonal cutting of Inconel 718 produced via powder bed fusion of metals using a laser beam system (PBF-LB/M), paying particular attention to the cutting energy, chip formation, geometrical defects, and microstructural deformation. Experiments are conducted on both wrought (W 718) and PBF-LB/M (PBF 718) Inconel 718, whereby the cutting speed and the anisotropy of the workpiece in the raw state play an important role. The results indicate that less cutting energy is consumed when cutting PBF 718 in the direction perpendicular to its build direction (BD), followed by cutting in its BD. Denser shearing-induced slip lines and relatively continuous chip morphology are found when cutting PBF 718 in its BD, moreover, the effect of cutting speed on shearing deformation of columnar grains under this condition is analysed. More importantly, this study identifies a significant geometrical defect phenomenon which is unique to PBF 718 and highly depends on the cutting speed and anisotropy of grain feature. A detailed characterisation shows that this behaviour is caused by tearing within the grains in the matrix material and not by the presence of hard inclusions, which has rarely been reported in the literature. The microstructure in the subsurface area exhibits that the density of grain boundaries in the cutting direction plays the key role in plastic deformation, as the machining process mainly causes dragging behaviour in the area below the machined surface. Thus, cutting PBF 718 in the direction perpendicular to its BD shows similar deformation layer to W 718, while cutting PBF 718 in its BD displays much stronger subsurface deformation. The obtained results greatly help to understand the cutting phenomena in post-machining of additively manufactured Ni-based components, especially the integrity for a better functional surface.

Correlation between surface texture and internal defects in laser powder-bed fusion additive manufacturing

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Surface texture measurement for additive manufacturing

Spattering mechanism of laser powder bed fusion additive manufacturing on heterogeneous surfaces

Defect-based analysis of the laser powder bed fusion process using X-ray data

In-Situ Monitoring for Defect Identification in Nickel Alloy Complex Geometries Fabricated by L-PBF Additive Manufacturing

The effect of primary processing parameters on surface roughness in laser powder bed additive manufacturing

Assessing Volumetric Energy Density as a Predictor of Defects in Laser Powder Bed Fusion 316L Stainless Steel

Effect of processing parameters on surface roughness, porosity and cracking of as-built IN738LC parts fabricated by laser powder bed fusion

Influence of Defects and Microstructure on the Thermal Expansion Behavior and the Mechanical Properties of Additively Manufactured Fe-36Ni

Texture-based residual stress analysis of laser powder bed fused Inconel 718 parts

Effect of Powder Characteristics on Relative Density and Porosity Formation During Electron Beam Selective Melting of Al2024 Aluminum Alloy

Metallurgical Defects and Roughness Investigation in the Laser Powder Bed Fusion Multi-Scanning Strategy of AlSi10Mg Parts

Assessment of Residual Stresses in Laser Powder Bed Fusion Manufactured IN 625

Investigation of the accuracy and roughness in the laser powder bed fusion process

Review of In Situ Detection and Ex Situ Characterization of Porosity in Laser Powder Bed Fusion Metal Additive Manufacturing

Relative Density Measurement of PBF-Manufactured 316L and AlSi10Mg Samples via Eddy Current Testing

Defect and Distortion in Powder Bed Fusion of Metal Additive Manufacturing Parts

Predicting Laser Powder Bed Fusion Defects Through In-Process Monitoring Data and Machine Learning

Pore defects in Laser Powder Bed Fusion: Formation mechanism, control method, and perspectives

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion