Abstract:Titanium alloys are known for being difficult to machine. Within the groups of Ti alloys, the machinability is reduced when going from the α-alloys, to α + β, and finally to near-β or β-alloys. Uncoated cemented carbide is traditionally used for machining these alloys and finding a suitable coating to improve the performance is a challenge due to the high strength of Ti alloys and the high chemical reactivity of Ti with tool and coating materials at the temperatures achieved during cutting. The PVD applied Ti x Al 1-x N (x = 0.4–0.7) is generally recommended for machining Ti alloys and a top layer of NbN has shown promising performance in milling applications. This study systematically explores the wear mechanisms of either uncoated WC-12%Co or its Ti 0.45 Al 0.55 N-NbN coated version in the milling of Ti alloys ranging from near-α (Ti-6Al-2Sn-4Zr-2Mo), α + β (Ti-6Al-2Sn-4Zr-6Mo), and near-β (Ti-5Al-5Mo-5 V-3Cr) alloys. The wear evolution is explored by studying as-worn tools and their cross-section using SEM-XEDS and EBSD after having reached 10%, 30%, 50%, and 100% of the full tool life at a flank wear criterion VB = 200 μm. The coating is removed within seconds of engagement and fails by cracking within the bulk and PVD droplet defects can initiate such cracks. Diffusional dissolution of the coating may be active on a minor scale, but the rapid mechanical failure shows the need for a more robust coating formulation. Exposed cemented carbide is worn at varying intensities when machining the Ti alloys. The highest wear rate is achieved in milling α + β Ti-6246, followed by a moderate wear rate in near-β Ti-5553, and with a slower wear rate in milling near-α Ti-6242 which is explained varying intensities in oxidation wear, diffusional dissolution, and mechanical cracking. Diffusional loss of C gives rounder WC grains and remaining W at the interface is removed by the chip flow. Diffusional loss of Co gives reduced grain bonding and loss of the dampening effect that leads to fractures in WC grains. Specifically in milling α + β Ti-6246 and in minor scale in near-α Ti-6242, there is formation of CoWO 4 ceramic present several μm into the tool and its formation is facilitated by the oxidation of binder with resolved W. Fractures within the CoWO 4 explains the high wear rate. Cracks also propagate in binder regions initiated from weakened interface regions due to diffusional loss of C and Co.

Effect of milling of C and Ti mixture as ceramic coating on the properties of 7Ch3 tool steel during plasma spray process

Fabrication and Characterization of Plasma-Sprayed Cr3C2-25 Cr/Al2O3-40TiO2 Duplex Coating

Experimental Investigation on Tool Wear Characteristics of PVD and CVD Coatings During Face Milling of Ti6242S and Ti-555 Titanium Alloys

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment

Effect of Dispersed TiC Content on the Microstructure and Thermal Property of Shrouded-Plasma-Sprayed FeAl/TiC Composite Coatings

The effect of substrate surface integrity on the surface properties of TiCrN coating applied via the CAE‐PVD method

In-situ TiC-Ti5Si3-SiC composite coatings prepared by plasma spraying

Fabrication of Titanium Carbide Film on Bearing Steel by Plasma Immersion Ion Implantation and Deposition

Influence of Ti on the Microstructure and Performance of Fe-Cr Alloy Cladding Layer

Microstructure and Properties of Al_2O_3-13wt%TiO_2 Coatings Fabricated by Plasma Spraying and Laser Remelting on Titanium Alloy

Wear Resistance and Titanium Adhesion of Cathodic Arc Deposited Multi-Component Coatings for Carbide End Mills at the Trochoidal Milling of Titanium Alloy

Effects of Cr3 C2 on Microstructure and Wear Resistance of Cobalt-Base Alloy Coating Deposited by Plasma Transferred Arc Surfacing

TiC-TiSi2-Al2O3 composite coatings prepared by spray drying, heat treatment and plasma spraying

Hybrid structure and dry sliding tribological characteristics of in-situ synthesizing TiC-M7C3

Properties of Reactive Plasma Sprayed Tib2-Tic0.3n0.7 Based Composite Coatings with Cr Addition and Laser Surface Treatment

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Fabrication of plasma-sprayed TiC-Ti5Si3-Ti3SiC2 composite coatings from the annealed Ti/SiC powders

Microstructure and tribological properties of Al-30Si-5Cu composite coating reinforced with ceramic phases synthesized in situ by plasma spraying

Effect of Dispersed TiC Content on the Microstructure and Thermal Expansion Behavior of Shrouded-Plasma-Sprayed FeAl/TiC Composite Coatings

The Effect of Powder Preparation Method on the Corrosion and Mechanical Properties of TiN-based Coatings by Reactive Plasma Spraying

Microstructure and Tribological Property of TiC-Mo Composite Coating Prepared by Vacuum Plasma Spraying