Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Culturing and Bonding of Diatom on a Microfluidic Chip for Biosensing Application

Diatom based biosensor for high sensitive fluorescence detection based on a spin-on glass bonding technique

Fabrication of microcoil/microsprings for novel chemical and biological sensing

Assembling And Patterning Of Diatom Frustules Onto Pdms Substrates Using Photoassisted Chemical Bonding

Bonding of Diatom Frustules and Si Substrates Assisted by Hydrofluoric Acid

Composite Diatom Fluorescent Sensor Substrate Enriched with CdSe/ZnS Quantum Dots on the Surface by Biofabrication

A Universal Bonding Method for Preparation of Microfluidic Biosensor

Micro-Arraying of Nanostructured Diatom Microshells on Glass Substrate Using Ethylene-Vinyl Acetate Copolymer and Photolithography Technology for Fluorescence Spectroscopy Application

Culture and Motion Analysis of Diatom Bacillaria Paradoxa on a Microfluidic Platform.

Key Factors Influencing the Optical Detection of Biomolecules by Their Evaporative Assembly on Diatom Frustules

Fabrication of Micro/Nanofluidic Chip on Glass Substrate and Its Application for Electrokinetic Concentration of Proteins

Hydrofluoric Acid-Assisted Bonding of Diatoms with Sio2-Based Substrates for Microsystem Application

Fabrication of a Surface Stress-Based PDMS Micro-Membrane Biosensor

Fabrication of a chemosensor array on a microfluidic device by a simple gel-based method

Bonding of Glass-Based Microfluidic Chips at Low- or Room-Temperature in Routine Laboratory

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

A Simple Method For Fabrication Of Microstructures Using A Pdms Stamp

Microfabrication of chamber-type microchips and its applications for chemical sensors

Diatomite Photonic Crystals for Facile On-Chip Chromatography and Sensing of Harmful Ingredients from Food

Observation Interface of PDMS Membrane in a Microfluidic Chip Based on One-Step Molding

Fabrication of PDMS Chips by Laser Engraving for Protein Enrichments