Abstract:To fabricate complex structures made of nitinol (NiTi), additive manufacturing (AM) has drawn significant interest. However, due to its high microstructural and compositional sensitivities, it is still challenging to fabricate functional NiTi devices via AM. It has been widely reported that evaporation of Ni and formation of precipitation phases during fabrication significantly diverts the expected functional properties. To this date, laser powder bed fusion (LPBF) was the choice among many AM techniques to fabricate NiTi devices but successfully only on a NiTi substrate because of its poor bonding to other substrates (i.e., steel and Ti). Expensive NiTi substrate significantly limits the economic feasibility of fabricating NiTi parts. In this work, a multi-step approach was systematically developed, which enabled printing NiTi on a Ti substrate using a very low laser energy density of 35 J/mm 3 without any visible defect. This printing method avoided the Ni evaporation as well as facilitated fast cooling by avoiding the formation of undesirable precipitation phase during solidification. The phase transformation peaks in differential scanning calorimetry (DSC) data clearly indicated that the printed sample is in austenite (B2) phase at room temperature. In the cyclic compressive test, the samples showed superelasticity with recovery ratios of 73 % and 92 % in the 1st and 10th cycle, respectively, from an imposed strain of 8.04 %. Electron backscatter diffraction (EBSD) analysis proved the presence of major [001] oriented B2 grains along the building direction which was attributed to the shallower melt pool obtained by the low laser energy density scanning. It was also found that higher oxygen level in the printing chamber reduced the austenite finish (A f ) temperature and negatively affected the printability. These results showed the feasibility of LPBF in printing NiTi on a substrate other than nitinol, providing a possible route to reduce the cost of NiTi fabrication via AM with improved superelastic properties.

Manufacturing three-dimensional nickel titanium articles using layer-by-layer laser-melting technology

Advances in Selective Laser Melting of Nitinol Shape Memory Alloy Part Production

Selective Laser Melting of Pre-Alloyed NiTi Powder: Single-Track Study and FE Modeling with Heat Source Calibration

Nickel‐Titanium Alloy Laser Micromachining: A Review of Nitinol Laser Processes and Optimization for High‐Speed Laser Cutting

Laser powder bed fusion of nitinol shape memory alloy with superelastic characteristics on Ti substrate

The Preparation of TiC/TiN Composites by Selective Laser Melting

A Review on Design and Mechanical Properties of Additively Manufactured NiTi Implants for Orthopedic Applications

Nickel-titanium shape memory alloys made by selective laser melting: a review on process optimisation

SLM Additive Manufacturing of NiTi Porous Implants: A Review of Constitutive Models, Finite Element Simulations, Manufacturing, Heat Treatment, Mechanical, and Biomedical Studies

Achieving superelasticity in additively manufactured NiTi in compression without post-process heat treatment

Laser powder bed fusion additive manufacturing of NiTi shape memory alloys: A review

Nitinol: From historical milestones to functional properties and biomedical applications

Superelastic NiTi Functional Components by High-Precision Laser Powder Bed Fusion Process: The Critical Roles of Energy Density and Minimal Feature Size

Micro selective laser melting of NiTi shape memory alloy: Defects, microstructures and thermal/mechanical properties

SLM-built titanium materials: great potential of developing microstructure and properties for biomedical applications: a review

Features of obtaining TiNi alloy samples from commercial powders with high oxygen content using the SLM technique

In vivo biocompatibility evaluation of 3D-printed nickel-titanium fabricated by selective laser melting

Mechanical Evaluation of Selective Laser Melted Ni-Rich NiTi: Compression, Tension, and Torsion

Research Status and Prospect of Additive Manufactured Nickel-Titanium Shape Memory Alloys

Selective laser melting fabrication of body-temperature shape memory NiTi alloy for 4D-printed orthopedic implants