Abstract:Polymer-based composites for steel structure coating are an effective strategy to improve tribological properties and service durability under hygrothermal aging conditions. In the present paper, epoxy resin was improved by mechanical reinforcement and frictional lubrication fillers, and a kind of multi-filler reinforced epoxy composite (MFREC) was successfully prepared. Water uptake behavior, mechanical and thermal property evolution, friction behavior and wear mechanism as well as micro-topography analysis of MFREC under hygrothermal aging were conducted and discussed in detail. The research results showed that the water uptake curve of MFREC after distilled water and 5 wt.% NaCl water solution immersions confirmed the two-stage diffusion model, where the quasi-equilibrium water uptakes were 4.23% and 3.67%, respectively. Additionally, the fundamental reason for the degradation of the mechanical and thermal properties of MFREC was the hydrolysis of the resin and the de-bonding of the fillers/matrix interface. The interface shear strength of MFREC adhesive and steel gradually decreased with the hygrothermal aging, but did not lose the bonding property, because the uniformly dispersed multi-fillers can fill the internal defects of the matrix and prolong the crack propagation path to block the effect. Before hygrothermal aging, MFREC had excellent friction and wear resistance compared to resin matrix, especially under water lubrication conditions. The anti-wear rate of MFREC increased by up to 59.6% compared to the room temperature dry test environment due to the coupling effects of the water lubrication and anti-friction characteristics of modified fillers. Hygrothermal aging had little effect (<12%) on the friction coefficient of MFREC, but the anti-wear properties decreased significantly, especially the Ws increased by 255.1% under the 60 °C immersion condition. Because the degradation of thermal/mechanical properties was not enough to resist the high shear stress of the steel ball, leading to severe fatigue wear.

Study of Cu–Zn–Co ternary alloy-coated steel cord in cobalt-free skim compound

Tailoring α/β-Brass coating on steel via one-bath co-deposition: Influence of current density and electrolyte composition in pyrophosphate system

Microstructural changes and dry sliding wear behavior of Cu-15Ni-8Sn-0.5Co alloy during deformation and aging treatment

Tribology, corrosion, and tribocorrosion performance of aged lightweight steels: Effects of oxide film and carbide

Quantitative study of the effect of high-performance zinc alloy coating technology on the life of mechanical components

Microstructure and tribological performance of Co-B intermetallic compounds under water environment

Effect of aging treatment on the electrical sliding wear behavior of Cu–Cr–Zr alloy

Research on Tribological and Wear Properties of Cu Coating on TC4 Alloy

A Study on the Tribological Performance of an Organic Cadmium Compound as a Lubricant Additive

Effect of WC-17Co Content on Microstructure, Mechanical Properties and Wear Resistance of WC-17Co/Ni Composites Produced with Cold Spraying

Effect of Co content on the microstructure, mechanical properties and corrosion behavior of Zr alloys

Effect of cobalt on precipitation in Fe-Cr-Co-Mo-Ni-C stainless steels

Effect of hygrothermal aging on the friction behavior and wear mechanism of the multi-filler reinforced epoxy composites for coated steel

In Situ Thermal Interactions of Cu-Based Anti-Corrosion Coatings on Steel Implemented by Surface Alloying

Excellent Corrosion and Wear Resistance of Amorphous and Crystalline ZrCoAl Alloys

Study on tribological properties and action mechanism of organic cadmium compound in lubricants

STUDY ON ABRASION MECHANISM OF SHORT CARBON FIBER REINFORCED Cu ALLOY MATRIX COMPOSITES

An Experimental Study on the Tensile Mechanical Behavior of Steel Cords for Radial Tires

An investigation of fretting wear behaviors of bonded solid lubricant coatings

Study of structural and tribological properties of MoS2-Zr composite coatings

Effects of Tribo-Film on Wear Resistance of Additive Manufactured Cobalt-Based Alloys During the Sliding Process