Abstract:The purpose of strengthened plasters (interior applications) and renders (exterior applications) in this paper is to control cracks at the interface between the main structure and the infill wall rather than strengthen masonry and reinforced concrete structures. Cracks in plasters and renders have caused severe issues that need to be resolved urgently. Cracks affect not only the aesthetics but also the normal use of a building. The presence of cracks changes the perceptions of the owners of a structure, forcing them to question its safety and even take legal action against its developer. Consequently, the present paper discusses the effects of different strengthening materials on the tensile behaviour of plasters and renders, particularly on the first cracking. One test group without strengthening materials and six test groups with strengthening materials were tested under uniaxial tensile loads. Each experimental group included the same six specimens. A glass fibre-reinforced polymer (GFRP) grid, two types of basalt fibre-reinforced polymer (BFRP) grids, and three types of welded wire meshes (WWMs) were selected as the strengthening materials in the tests. Four types of plasters and renders were used: cement mortar, anti-crack mortar, gypsum plaster, and thermal insulation mortar. The crack pattern, stain–stress relationship, first cracking strain, energy dissipation capacity in the uncracked stage, and microstructure were investigated to gain better insight into the tensile behaviour of the plasters and renders. It was found that a strengthening material with a small mesh size resulted in numerous cracks and a narrow crack spacing. The stress–strain curves of the strengthened specimens could be divided into uncracked and cracked stages. The higher slopes in both stages of the strengthened specimens could be attributed to the higher longitudinal strain coefficient, smaller opening size, and larger cross-sectional area of each strand of the strengthening materials. The first cracking strain of the unreinforced specimen was smaller than that of a strengthened specimen. Stronger bond strength between plaster/render and strengthening material, smaller mesh size and greater cross-sectional area of each strand of strengthening material led to the larger first cracking strain. The energy dissipation capacity in the uncracked stage of the strengthened thermal insulation mortar was the least. The energy dissipation capabilities in the uncracked stage of the plasters/renders reinforced with BFRP grid-2 and WWM-3 were the second-highest and highest, respectively. The bond strengths of the GFRP and BFRP grids to the plasters/renders were stronger than those of the WWMs. The bond strengths between the gypsum plaster and the reinforcing materials were the highest, whereas those between the thermal insulation mortar and the strengthening materials were the lowest. Additionally, stress–strain relationships were proposed for the strengthened plasters and renders; the results were found to be in good agreement with the test results.

In-Plane Strengthening of Unreinforced Masonry Walls by Glass Fiber-Reinforced Polyurea

Out-of-Plane Strengthening of Unreinforced Masonry Walls by Glass Fiber-Reinforced Polyurea

Effect of Different Strengthening Materials on Tensile Behaviour of Plasters and Renders

In-Plane Shear Behavior of Unreinforced Masonry Wall Strengthened with Bamboo Fiber Textile-Reinforced Geopolymer Mortar

Improvement of Flexural and Shear Strength of RC Beam Reinforced by Glass Fiber-Reinforced Polyurea (GFRPU)

Out-of-plane strengthening of URM walls using different fiber-reinforced materials

Strengthening Effect Evaluation of Developed Stiff-Type Polyurea Sprayed on Masonry Beam Surface Under Static Loading in Experimental and Numerical Tests

Load Capacity of Concrete Masonry Block Walls Strengthened with Epoxy-bonded GFRP Sheets

Quasi-static, Cyclic Loading Tests of RAC Brick Masonry Walls Strengthened by Basalt Textile Reinforced Concrete

Compressive and Shear Behavior of Masonry Reinforced with Ultra-Rapid-Hardening Fiber-Reinforced Mortar (URH-FRM)

Investigating the Retrofitting Effect of Fiber-Reinforced Plastic and Steel Mesh Casting on Unreinforced Masonry Walls

In-Plane Shear Strengthening of Masonry Wallettes Using Ultra-High Performance Concrete Precast Plates

Enhancement of the impact resistance of masonry walls using fiber-reinforced polymer composites

Enhancement of Durability of Glass Fiber-Reinforced Cement with PVA

Experimental In-Plane Shear Performance of Masonry Infill Walls Assembled with Cementitious Matrix–Grid Composites

Experimental Study of Masonry Walls Strengthened with Cfrp

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Seismic Performance of Unreinforced Masonry Walls with Various Retrofitting Methods

Strengthening of Masonry Structures with FRP Composites

MECHANICAL BEHAVIOR OF MASONRY WALLS STRENGTHENED WITH CFRP

In-Plane Lateral Response of a Full-Scale Masonry Subassemblage with and without an Inorganic Matrix-Grid Strengthening System