Abstract:The addition of hollow aluminium oxide bubbles to the 7075 aluminium matrix results in a lightweight syntactic foam with a reduced density and an increased peak compression strength. The presence of ceramic bubbles also aids in a reduced coefficient of thermal expansion and thermal conductivity in comparison to aluminium alloys. In spite of their enhanced material properties, the inclusion of hollow aluminium oxide bubbles presents the challenge of poor machinability. In order to elucidate the problem of poor surface machinability, an attempt has been made to develop a thermo-mechanical finite element machining model using AdvantEdgeTM software with which surface quality and machined syntactic foam material can be analyzed. If the novel model developed is combined with virtual reality technology, CNC technicians can observe the machining results to evaluate and optimize the machining program. The main novelty behind this software is that the material foam is assumed as a homogeneous material model for simplifying the material model as a complex heterogeneous material system. The input parameters used in this study are cutting speed, feed, average size and volume fraction of hollow aluminium oxide bubbles, and coolant. For the output parameters, the numerical analysis showed a 6.24% increase in peak tensile machining induced stress as well as a 51.49% increase in peak cutting temperature as cutting speed (25 m/min to 100 m/min) and uncut chip thickness (0.07 mm to 0.2 mm) were increased. The average size and volume fraction of hollow aluminium oxide bubbles showed a significant impact on the magnitude of cutting forces and the depth of tensile induced stress distribution. It was observed on the machined surface that, as the average size of hollow aluminium oxide bubbles became coarser, the peak machining induced tensile stress on the cut surface reduced by 4.47%. It was also noted that an increase in the volume fraction of hollow aluminium oxide bubbles led to an increase in both the peak machining induced tensile stress and the peak cutting temperature by 29.36% and 20.11%, respectively. This study also showed the influence of the ceramic hollow bubbles on plastic deformation behavior in 7075 aluminium matrix; the machining conditions for obtaining a favorable stress distribution in the machined surface and sub-surface of 7075 closed cell syntactic foam are also presented.

High-speed cryogenic machining of the carbon nanotube reinforced nanocomposites: Finite element analysis and simulation

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Machinability analysis of dry and liquid nitrogen–based cryogenic cutting of Inconel 718: experimental and FE analysis

Effect of cooling and lubrication conditions on the variable angle milling of unidirectional CFRP with PCD Tools

Experimental Study on High-Speed Milling of SiCf/SiC Composites with PCD and CVD Diamond Tools

Research on cryogenic high-speed drilling performance of metal matrix composite materials (Al/SiC) using cryogenically treated drills

Sustainable Drilling of Nano SiC Reinforced Al Matrix Composites Using MQL and Cryogenic Cooling for Achieving the Better Surface Integrity

Correction of the constitutive model and analysis of chip formation in cryogenic machining of TA15 titanium alloy

Tool wear and surface quality during milling CFRP laminates under dry and LN2-based cryogenic conditions

Tough-brittle transition mechanism and specific cutting energy analysis during cryogenic machining of Ti–6Al–4V alloy

Effect of Cryogenic Cooling on Mechanical Properties and Cutting Force of 6061 Aluminum Alloy

Performance and mechanism evaluation during milling of CFRP laminates under cryogenic-based conditions

Precision machining performance and mechanism of Ni/Ni 3 Al alloy under cryogenic temperature

Application of grey-ANFIS system to optimize the drilling characteristics of nano SiC reinforced Al matrix composites

Computational Analysis of Machining Induced Stress Distribution during Dry and Cryogenic Orthogonal Cutting of 7075 Aluminium Closed Cell Syntactic Foams

Analysis of the influence of cutting parameters on surface roughness and cutting forces in high speed face milling of Al/SiC MMC

Milling performance of cryogenic cooled titanium alloy thin-walled parts based on cantilever sheet

Comprehensive investigation of the effect of cryogenic process on machining of Inconel 718 superalloys with uncoated end mills

Investigation of the Effects of Cooling and Lubricating Strategies on Tribological Characteristics in Machining of Hybrid Composites

A Novel Finite Element Model for Thermally Induced Machining of Ti6Al4V

Effect of Cryogenic Cooling on Cutting Surface Integrity and Surface Functional Properties of 6061 Aluminum Alloy