Abstract:3D printing has revolutionized solid oxide fuel cell (SOFC) by introducing complicated structure and new functionalities that cannot be realized using traditional preparation process. This work provides guide and insights into the application of direct-writing 3D printing to fabricate the patterned electrolyte|electrode interface for the anode-supported SOFC using 3 mol % yttria-stabilized zirconia-nickel oxide (3YSZ-NiO) as the anode substrate material. The parameters that affected the shaping and performance of SOFC including the rheological properties of 3YSZ-NiO anode paste, the printing parameters, and the heat treatment process of the pre-sintered anode substrate were evaluated. The prepared 3YSZ-NiO paste exhibited a typical shear-thinning characteristic, "yielding" solid-like behavior, and time- and temperature-independent stability performance, which ensured the paste suitable for extrusion while allowing the shape of the printed body to be maintained after extrusion during the direct-writing printing process. The as-prepared anode paste, combined with the obtained values of 0.1 MPa, 100 mm s −1 , 100 rpm, and 0.3 mm for printing parameters of the extrusion pressure, the printing speed, the screw speed, and the nozzle diameter, respectively, as well as the devised heat treatment program for the pre-sintered 3YSZ-NiO anode substrate, successfully produced defect-free corrugated anode substrates. The cell made from the as-mentioned anode substrate showed an open circuit voltage of 1.02 V and a maximum power density of 619.44 mW cm −2 at 850 °C, which was comparable to the other identical cells fabricated by traditional and other 3D printing processes. Using the 3D printing process shown here, the preparation time of patterned anode substrate can be reduced and simplified.

Characterisation of NiO-YSZ Porous Anode-Support for Solid Oxide Fuel Cells Fabricated by Ceramic Injection Moulding

Fabrication of tubular NiO/YSZ anode-support of solid oxide fuel cell by gelcasting

Fabrication and Characterization of Large Size Anode Substrate of Solid Oxide Full Cell

A Phase Inversion/Sintering Process to Fabricate Nickel/Yttria-Stabilized Zirconia Hollow Fibers As the Anode Support for Micro-Tubular Solid Oxide Fuel Cells

Preparation of Porous NiO-Ce0.8Sm0.2O1.9 Ceramics for Anode-supported Low-temperatureSolid Oxide Fuel Cells

Microstructure Tailoring of the Nickel Oxide-Yttria-Stabilized Zirconia Hollow Fibers Toward High-Performance Microtubular Solid Oxide Fuel Cells

Effect of Preparation Methods on the Properties of Ni-Ysz Cermets for Sofc Anodes

Fabrication and Evaluation of a Ni/La0.75Sr0.25Cr0.5Fe0.5O3−δ Co-Impregnated Yttria-Stabilized Zirconia Anode for Single-Chamber Solid Oxide Fuel Cells

Preparation of Ni–YSZ Cermet through Reduction of NiO–YSZ Ceramic for SOFC Anode

Effect of Composite Pore-Former on the Fabrication and Performance of Anode-Supported Membranes for SOFCs

Preparation and Characteristics of Anode-Supported Solid Oxide Fuel Cells by Wet Ceramic Powder Process

Application of 8YSZ Nanopowder Synthesized by the Modified Solvothermal Process for Anode Supported Solid Oxide Fuel Cells

Effect of Composition of NiO/YSZ Anode on the Polarization Characteristics of SOFC Fabricated by Atmospheric Plasma Spraying

Novel Co-precipitation method to synthesize NiO-YSZ nanocomposite powder for solid oxide fuel cell

Sintering Process Simulation of a Solid Oxide Fuel Cell Anode and Its Predicted Thermophysical Properties

Fabrication and Interfacial Structure of Ni-YSZ-LSM Porous Scaffold for Solid Oxide Fuel Cells

Fabrication of Anode Supported Micro Tubular SOFCS by Dip-Coating Process on NiO/YSZ Hollow Fibers

Vat Photopolymerization 3D Printing of NiO-YSZ Anode for Solid Oxide Fuel Cells

Preparation and Properties of Direct-Methane Solid Oxide Fuel Cell Based on a Graded Cu-CeO<sub>2</sub>-Ni-YSZ Composite Anode

A Symmetrical Solid Oxide Fuel Cell Prepared by Dry-Pressing and Impregnating Methods

Facile preparation of patterned anode substrate for solid oxide fuel cells by direct-writing 3D printing technology