Abstract:Laser metal deposition (LMD) additive manufacturing process was applied to produce ultrafine TiC particle reinforced Inconel 625 composite parts. The effects of laser energy input per unit length (LEIPUL) on microstructure development, densification response, and mechanical performance including wear performance and tensile properties were comprehensively studied. A relationship of processing conditions, microstructural characteristics, mechanical performance, and underlying strengthening mechanisms was proposed for a successful LMD of high-performance Inconel based composite parts. It revealed that using an insufficient LEIPUL of 33kJ/m lowered the densification behavior of LMD-processed parts, due to the appearance of residual large-sized pores in inter-layer areas of the parts. An increase in LEIPUL above 100kJ/m yielded the near fully dense composite parts after LMD. On increasing LEIPUL, the TiC reinforcing particles became significantly refined and smoothened via the elevated melting of particle surfaces and the dispersion state of ultra-fine reinforcing particles was homogenized due to the efficient action of Marangoni flow within the molten pool. The dendrites of Ni–Cr γ matrix underwent a successive change from an insufficiently developed, disordered microstructure to a refined, ordered microstructure with the increase of LEIPUL. However, the columnar dendrites of the matrix were coarsened apparently at an excessive LEIPUL of 160kJ/m because of the elevated thermalization of the input laser energy. The formation of the refined columnar dendrites of Ni–Cr γ matrix combined with the homogeneously distributed ultra-fine reinforcing particles contributed to the enhancement of wear performance of LMD-processed composites with a considerably low coefficient of friction (COF) of 0.30 and reduced wear rate of 1.3×10−4mm3/Nm. The optimally prepared TiC/Inconel 625 composite parts demonstrated a ductile fracture mode with a sufficiently high tensile strength of 1077.3MPa, yield strength of 659.3MPa, and elongation of 20.7%. The superior tensile properties of LMD-processed parts were attributed to the significant grain refinement effect of the matrix during laser processing and the efficient prohibition of ultrafine reinforcing particles on the mobility of dislocations.

Tensile Fracture Behavior and Failure Mechanism of Additively-Manufactured AISI 4140 Low Alloy Steel by Laser Engineered Net Shaping

Laser Engineered Net Shaping of Nickel-Based Superalloy Inconel 718 Powders onto AISI 4140 Alloy Steel Substrates: Interface Bond and Fracture Failure Mechanism

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Mechanical properties and microstructure evolution of additive manufactured 316L stainless steel under dynamic loading

Microstructure and fracture behavior of 90W-7Ni-3Fe alloy fabricated by laser directed energy deposition

Competitive failure analysis on tensile fracture of laser-deposited material for martensitic stainless steel

Porosity effect on tensile behavior of Ti-6Al-4V specimens produced by laser engineered net shaping technology

Microstructure evolution and formation mechanism of a crack-free nickel-based superalloy fabricated by laser engineered net shaping

Microstructures and Mechanical Behaviors of Additive Manufactured Inconel 625 alloys via Selective Laser Melting and Laser Engineered Net Shaping

Deformation-Induced Strengthening Mechanism in a Newly Designed L-40 Tool Steel Manufactured by Laser Powder Bed Fusion

In Situ Tensile Observation of the Effect of Annealing on Fracture Behavior of Laser Additive Manufactured Titanium Alloy

Tensile Properties and Microstructural Evolution of 17–4 PH Stainless Steel Fabricated by Laser Hybrid Additive Manufacturing Technology

Anisotropic dynamic compression response of an ultra-high strength steel fabricated by laser hybrid additive manufacturing

Fatigue and tensile deformation behaviors of laser powder bed fused 304L austenitic stainless steel

High Cycle Fatigue Behavior of 316L Steel Fabricated by Laser Powder Bed Fusion: Effects of Surface Defect and Loading Mode

Microstructural Feature-Driven Machine Learning for Predicting Mechanical Tensile Strength of Laser Powder Bed Fusion (L-PBF) Additively Manufactured Ti6Al4V Alloy

Failure Behavior of Laser Metal Deposited Additive Manufacturing Ti-6Al-4V: Effects of Stress State and Initial Defects

Laser Additive Manufacturing of Ultrafine Tic Particle Reinforced Inconel 625 Based Composite Parts: Tailored Microstructures and Enhanced Performance

In-Situ SEM Study on Deformation and Failure Mechanism of TC4 Titanium Alloy by Laser Additive Manufacturing