Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Effects of Chemical Functionalization of MWCNTs on the Structural and Physical Properties of Elastomeric Copolyetherester-based Composite Fibers

Hindered phenol grafted carbon nanotubes for enhanced thermal oxidative stability of polyethylene

Functionalization of Carbon Nanotubes by Corona‐Discharge Induced Graft Polymerization for the Reinforcement of Epoxy Nanocomposites

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Effect of Carbon Nanotubes on the Mechanical Properties and Crystallization Behavior of Poly(ether Ether Ketone)

Electrical and thermal characteristics of MWCNTs modified carbon fiber/epoxy composite films

Enhanced thermomechanical properties of epoxy-multiwalled CNT nano-composites

Carbon fiber coating with MWCNT in the presence of polyethyleneimine of different molecular weights and the effect on the interfacial shear strength of thermoplastic and thermosetting carbon fiber composites

Synthesis and Characterization of Nanostructured Copolymer-Grafted Multiwalled Carbon Nanotube Composite Thermoplastic Elastomers Toward Unique Morphology and Strongly Enhanced Mechanical Properties

Effect of Multi-Walled Carbon Nanotubes on the Properties of Polyoxymethylene

Effects of Amino‐functionalized Carbon Nanotubes on the Properties of Amine‐terminated Butadiene–acrylonitrile Rubber‐toughened Epoxy Resins

Dispersion Stability of Functionalized MWCNT in the Epoxy–amine System and Its Effects on Mechanical and Interfacial Properties of Carbon Fiber Composites

Improvement Effect of Functionalized Cnts on Mechanical and Thermal Properties of Epoxy Matrix

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

Effect of modified filler surfaces and filler-tethered polymer chains on morphology and physical properties of poly(azo-pyridyl-urethane)/multi-walled carbon nanotube nanocomposites

MWCNT functionalized CF/PEKK composites with optimized EMI shielding and mechanical properties

Effect of NH2-MWCNTs sprayed carbon fiber on the mechanical properties of carbon fiber reinforced polycarbonate composite for lightweight structural applications

Effectiveness of multi‐walled carbon nanotube on the improvement of tensile, flexural, and low‐velocity impact properties of hybrid Kevlar/carbon fiber reinforced epoxy‐based composites

Effect of MWCNTs surface functionalization on the characterization of PVA/MWCNTs nanocomposites

Carboxyl-terminated Butadiene-Acrylonitrile-toughened Epoxy/carboxyl-Modified Carbon Nanotube Nanocomposites: Thermal and Mechanical Properties

Influence of a Liquid-Like MWCNT Reinforcement on Interfacial and Mechanical Properties of Carbon Fiber Filament Winding Composites