Abstract:Single hat sectioned hybrid beams composed of aluminum and Carbon Fiber Reinforced Polymeric materials (CFRP), intended for structural applications in the automotive and aviation sectors, have been studied from the point of their energy absorption capabilities when submitted to transverse low-velocity impact loading. Carbon fiber-epoxy composite prepregs were placed on the inside of the single hat sectioned aluminum sheet and completely cured in the autoclave under the recommended curing cycle. The bonding process between the aluminum sheet and composite layers was achieved by using 3M VHB™ 4930 double-sided acrylic foam tape. Bonding the aluminum and composite layers through adhesive tape eliminates the requirement of surface preparation of the aluminum layer through chemical etching or mechanical abrasion and thereby the strength of the metallic layer is not reduced due to the formation micropores during the chemical etching process. Results are shown in terms of load-displacement and damage morphologies diagrams; characteristic trends are compared and discussed. It was observed that the presence of viscoelastic adhesive tape material restricts the rupture (visual cracks) failure of the outer aluminum layer, resulting in the only impact-induced indentation for all impact energies. Numerical simulations were also performed to characterize and predict the failure mechanism of such hybrid beams when subjected to impact loading. Numerical predictions showed good correlation with experimental results for all impact histories at low and medium impact energies but a showed slight discrepancy for highest impact energy and were not able to successfully capture the system response in the unloading region. Current modeling does not consider damage healing or recovery with unloading and it is difficult to account for such change in material state. This study provides the low-velocity impact characteristics and collapse behavior of the hybrid hat sectioned beams under tensile and shear forces developed by impact loading by providing insight to their primary damage mechanisms relative to the impact energies. It was found that the primary damage of the specimen's changes from impact-induced indentation, minimal fiber breakage to partial perforation accompanied by larger indentation depth as the impact energy is increased from 6 to 12 J.

Low-velocity impact behavior of hybrid CFRP-elastomer-metal laminates in comparison with conventional fiber-metal laminates

Low velocity impact resistance of hybrid CFRP‐elastomer‐metal laminates: Influence of stacking sequence and impact conditions on damage mechanisms

Comparative study on low velocity impact response of carbon-fiber-reinforced polymer/ thermoplastic elastomer based fiber metal laminates with and without interleaving of elastomeric layer

Study of Low-Velocity Impact Behavior of Hybrid Fiber-Reinforced Metal Laminates

Low velocity impact response of fiber metal laminates with nano-patterned metal surfaces

On the influence of low-velocity impact damage on constrained-layer damping in hybrid CFRP-elastomer-metal laminates

Experimental and theoretical study on residual ultimate strength after impact of CF/PEEK-titanium hybrid laminates with nano-interfacial enhancement

Impact responses and residual flexural properties of narrow CFRP laminates

Behaviors of Composite Laminates under Low-Energy Impact Using a Novel Analytical Framework

Low-velocity Impact Behavior and Damage Mechanisms of Honeycomb Sandwich Structures with Elastomeric Interlayers in CFRP Skins

Study of the dynamic response and damage evolution of carbon fiber/ultra-thin stainless-steel strip fiber metal laminates under low-velocity impact

Effect of Volume Ratio and Hybrid Mode on Low-Velocity Impact Properties of Unidirectional Flax/carbon Fiber Hybrid Reinforced Polymer Composites

Experimental and Simulation Study on Failure of Thermoplastic Carbon Fiber Composite Laminates under Low-Velocity Impact

Research on Low-Velocity Impact Response of Novel Short-Fiber-Reinforced Composite Laminates

Improving the impact performance of natural fiber reinforced laminate through hybridization and layup design

Influence of UHMWPE fiber and Ti6Al4V metal surface treatments on the low-velocity impact behavior of thermoplastic fiber metal laminates

On the bending behavior of hybrid fiber–metal laminates (HFMLs) based on aluminum and glass/Kevlar fibers reinforced epoxy

Low-Velocity Impact Characteristics of Hybrid Aluminum/CFRP Single Hat Sectioned Beam Adhesively Bonded Using Adhesive Tape

An insight into the mechanical behavior and failure mechanism of CFRP/Al adhesively bonded structures subjected to low-velocity impact

Numerical modeling and experimental validation of low velocity impact of woven GFRP/CFRP composites

On impact behavior of fiber metal laminate (FML) structures: A state-of-the-art review