Abstract:Multi-pass TIG welding was conducted on plates (15×300×180 mm<sup>3</sup>) of aluminum alloy Al-5083 that usually serves as the component material in structural applications such as cryogenics and chemical processing industries. Porosity formation and solidification cracking are the most common defects when TIG welding Al-5083 alloy, which is sensitive to the welding heat input. In the experiment, the heat input was varied from 0.89 kJ/mm to 5 kJ/mm designed by the combination of welding torch travel speed and welding current. Tensile, micro-Vicker hardness and Charpy impact tests were executed to witness the impetus response of heat input on the mechanical properties of the joints. Radiographic inspection was performed to assess the joint's quality and welding defects. The results show that all the specimens displayed inferior mechanical properties as compared to the base alloy. It was established that porosity was progressively abridged by the increase of heat input. The results also clinched that the use of medium heat input (1 to 2 kJ/mm) offered the best mechanical properties by eradicating welding defects, in which only about 18.26 % of strength was lost. The yield strength of all the welded specimens remained unaffected indicated no influence of heat input. Partially melted zone (PMZ) width also affected by heat input, which became widened with the increase of heat input. The grain size of PMZ was found to be coarser than the respective grain size in the fusion zone. Charpy impact testing revealed that the absorbed energy by low heat input specimen (welded at high speed) was greater than that of high heat input (welded at low speed) because of low porosity and the formation of equiaxed grains which induce better impact toughness. Cryogenic (-196 °C) impact testing was also performed and the results corroborate that impact properties under the cryogenic environment revealed no appreciable change after welding at designated heat input. Finally, Macro and micro fractured surfaces of tensile and impact specimens were analyzed using Stereo and Scanning Electron Microscopy (SEM), which have supported the experimental findings.

Resistance Spot Welding of Aluminum 6063 Alloy for Aerospace Application: Improvement of Microstructural and Mechanical Properties

Quantifying structure-property relationships during resistance spot welding of an aluminum 6061-T6 joint

Optimization of process parameters of friction stir welded joints of dissimilar aluminum alloy by response surface methodology

Effect of Current on the Microstructural and Mechanical Properties of Mig Welded Aa6061 Aluminum Alloy

Orthogonal Optimization of Resistance Spot Welding Parameters and Microstructure and Mechanical Property of Aluminum Alloy/High Strength Steel Joint

Effect of Heat Input on the Microstructure and Mechanical Properties of Electron Beam-Welded AW2099 Aluminium-Lithium Alloy

Impact Welding of Aluminum to Copper and Stainless Steel by Vaporizing Foil Actuator: Effect of Heat Treatment Cycles on Mechanical Properties and Microstructure

Effect of Current on Mechanical Properties and Microstructure of Aluminum 6061 with Gas Tungsten Arc Welding Process

Corrosion Behavior of Friction Stir Welded AA8090-T87 Aluminum Alloy

Comparative Study on the Effect of External Magnetic Field on Aluminum Alloy 6061 and 7075 Resistance Spot-Welding Joints

Study on Morphology, Microstructure and Properties of 6063-T6 Aluminum Alloy Joints in MIG Welding

Experimental investigations on mechanical properties of AA6061-T6 aluminum alloy joined by laser welding using digital image correlation

Optimization of process parameters in friction stir welding of dissimilar aluminum alloys (AA6061–T6 and AA5052–H32)

Welding Characteristics Analysis and Application on Spacecraft of Friction Stir Welded 2A14-T6 Aluminum Alloy

Enhancing Mechanical Characteristics of 6061-T6 with 5083-H111 Aluminum Alloy Dissimilar Weldments: A New Pin Tool Design for Friction Stir Welding (FSW)

Friction Stir Welding of Al-Li AA2199: Parameters, Precipitates and Post Weld Heat Treatment

Microstructure, mechanical properties and corrosion of friction stir welded 6061 Aluminum Alloy

Analysis of Friction Stir Welded Joint Properties of 2A12 Aluminum Alloy

Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Improvement weldability of dissimilar joints (Ti6Al4V/Al6013) for aerospace industry by laser beam welding

Residual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds