Abstract:Inconel 617 nickel-based superalloy with 3 mm wall thickness was welded by laser beam using two different heat input welding parameters. The microstructure of the welded joint was observed by optical microscope and scanning electron microscope, and the mechanical properties of the welded joint at room temperature (25celcius) and high temperature (900celcius) were tested. The results show that the laser welding heat input has a significant effect on the microstructure and mechanical properties of Inconel 617 welded joints. The front width of the laser weld obtained by high heat input (200 J/mm) process parameters is 3.88 mm. The grain size in the middle of the weld fusion zone is coarse, and the grain orientation is disordered. The secondary dendrite arm spacing in the middle of the weld is large (6.71 mu m). The carbide particle size between the dendrites is coarse, and the solidification microsegregation of Mo, Cr alloy elements is serious. The width of heat affected zone is about 0.29 mm. The eutectic structure of gamma+carbide is formed in the grain boundary and grain interior. This is because during the heating process of the welding, the spherical carbide particles and the surrounding austenite in the heat-affected zone liquefy and the eutectic structure is formed during the solidification process after welding. The front width of the laser weld obtained by low heat input (90 J/mm) process parameters is 2.28 mm, the grains inside the weld are columnar which is formed by epitaxial growth along the fusion line and directional solidification along the heat flow direction. The secondary dendrite arm spacing in the middle of the weld is small (2.26 mu m), the carbide particles between dendrites are small, and the width of heat affected zone is about 0.15 mm. The tensile strength test at room temperature (25celcius) shows that the welded joints obtained under high heat input fracture from the middle of the weld, and the tensile strength and elongation decrease, which is caused by the segregation of solid solution elements in the weld. The welded joints obtained under low heat input fracture from the base metal. At high temperature (900celcius), all samples fracture from the base metal, which is due to the weakening of the grain boundary of the base metal at high temperatures.

Effect of Heat Input on the Microstructure and Mechanical Properties of Electron Beam-Welded AW2099 Aluminium-Lithium Alloy

Effect of heat input on microstructure and mechanical properties of IC10 Ni3Al-based superalloy electron beam welding joint

Microstructure and mechanical properties of electron beam welding of AlCoCrFeNi 2.1 eutectic high entropy alloy

Nanomechanical, mechanical and microstructural characterization of electron beam welded Al2219-T6 tempered aerospace grade alloy: A comprehensive study

Thermal stability of electron beam welded AlCoCrFeNi 2.1 alloy

Effect of heat input on microstructure and mechanical properties of laser welded joint of Inconel 617 nickel-based superalloy

Effect of post-weld heat treatment on the microstructure, phase composition and mechanical properties of dissimilar Al-Mg-Li/Al-Cu-Li laser welded joints

Evolution of Microstructure and Mechanical Properties of a Dissimilar Aluminium Alloy Weldment

Effect of Heat Input on the Microstructure and Mechanical Properties of 6060 Aluminum Alloy/Galvanized STEEL MIG Welding–Brazing Joints

Effects of heat input on the mechanical properties of butt-welded high and ultra-high strength steels

Effect of Current on the Microstructural and Mechanical Properties of Mig Welded Aa6061 Aluminum Alloy

Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Improved Joint Formation and Ductility during Electron-Beam Welding of Ti6Al4V and Al6082-T6 Dissimilar Alloys

Effect of post-weld heat treatment on microstructure and mechanical properties of 7055 aluminum alloy electron beam welded joint

Effects of Heat Input on Microstructure and Mechanical Properties of Laser-Welded Mg-Rare Earth Alloy

Impact Welding of Aluminum to Copper and Stainless Steel by Vaporizing Foil Actuator: Effect of Heat Treatment Cycles on Mechanical Properties and Microstructure

Effect of Heat Input on Microstructure and Properties of Dissimilar Laser Welded Joints Between TWIP and TRIP Steels

Resistance Spot Welding of Aluminum 6063 Alloy for Aerospace Application: Improvement of Microstructural and Mechanical Properties

Strength calculation and microstructure characterization of HAZ softening area in 6082-T6 aluminum alloy CMT welded joints

Comparative Study on Microstructure and Aluminum Distribution Between Laser Beam Welding and Electron Beam Welding of Ti–6Al–4V Alloy Plates

Effect of CMT Welding Heat Input on Microstructure and Properties of 2A14 Aluminum Alloy Joint