Abstract:The iron-based friction material was prepared directly from vanadium-bearing titanomagnetite concentrates by in situ selective carbothermal reactions and vacuum sintering. In this study, drawing on the extraordinary properties of graphene, experiments were conducted to evaluate the effects of graphene additives with a range of 0.2 to 1.0 wt pct on the microstructure and properties of iron-based materials sintered at 1050 C for 3 hours. The graphene was added in the form of copper-coated graphene to solve the weak bonding between matrix and graphene. The results show that the microstructure and properties of iron-based friction materials with graphene are significantly improved, especially the iron-based material containing 0.8 wt pct graphene. The graphene reduces the lamellar spacing of pearlite and contributes a more uniform growth of the grain due to its considerable high thermal conductivity. In addition, graphene could also facilitate the austenite transformation to refine the grain. As a result, with the increasing of the graphene content, the hardness is enhanced while the wear rate and friction coefficient are decreased. Particularly, the oxide films on the worn surface are accumulated and transform from FeO to Fe 3 O 4 and Fe 2 O 3 , together with the improved wear resistance, leading the wear behavior turns from severe abrasive and adhesive wear to mild abrasive wear. However, when the graphene content reaches to 1.0 wt pct, both the microstructure and tribological properties of the materials deteriorate again due to the aggregation of graphene. Graphical

Influence of Mn on the iron-based friction material directly prepared by in situ carbothermic reaction from vanadium-bearing titanomagnetite concentrates

Investigating Microstructural Evolution and Its Influence on Tribological Behaviors of In-Situ Formed VCp Reinforced Iron-Based Composites with Variable Mn Content

Effects of Graphene Additions on Iron-Based Friction Material Prepared From Vanadium-Bearing Titanomagnetite Concentrates Directly

Effect of Surface-Modified Graphene Addition on In Situ Synthesized Iron-Based Friction Materials

Effects of Fe2+ content in raw materials on Mn–Zn ferrite magnetic properties

Tribological properties of compacted graphite cast iron bearing vanadium under dry sliding

The investigation on friction and wear properties of cast iron matrix surface compact vanadium carbide layer

Effect of Preformed Calcium Ferrite Addition on Sintering Behavior of Vanadium Titanium Magnetite Ore

Effect of diboron trioxide on the crushing strength and smelting mechanism of high-chromium vanadium–titanium magnetite pellets

Effect of V and Mn Addition on the HAZ Softening and Tensile Properties of Friction Stir Welded Martensitic Steel

Effects of MnO on the smelting process of vanadium titanomagnetite pre-reduced pellets in an electric furnace

Enrichment and reconfiguration of titanium-bearing phase in vortex smelting reduction process of vanadium–titanium magnetite

Effect of Frictional Pair Materials on Tribological Behavior of Molybdenum Dithiocarbomate As an Additive

A Study of Friction-Induced Martensitic Transformation for Austenitic Manganese Steel

Microstructure, Mechanical and Tribological Properties of Mo-V-N Films by Reactive Magnetron Sputtering

The Effect of Vanadium Content Coupling with Heat Treatment Process on the Properties of Low-Vanadium Wear-Resistant Alloy

Influence of Molybdenum Content and Load on the Tribological Behaviors of In-Situ Cr3C2-20 Wt % Ni Composites

Effects of in-situ tribochemical treatment on mechanical property and tribological behavior of 45 steel

Investigation of the elevated temperature tribological property and wear mechanism of Fe‐15Cu‐0.8C materials containing Mo‐coated MoS2 powders

Experimental Study on the Friction of Isotropic Magnetorheological Elastomer Materials

Influence of Graphite Morphology and Chromium Content on Tribological Properties of Cast Iron under Dry Sliding