Abstract:High-efficiency and low-cost hot forming technologies for titanium alloys have been developed for producing complex-shaped, thin-walled tubular components under non-superplastic forming conditions. Under these forming conditions, there exist complex and highly integrated material evolution processes including microscopic heterogeneous deformation, microstructure evolution and damage behaviour. This paper presents an integrated crystal plasticity finite element model of near-α titanium alloys during non-superplastic hot deformation conditions considering grain boundary sliding (GBS), dynamic recrystallisation (DRX), as well as void evolution. The polycrystalline model of a near-α TA15 titanium alloy was established, containing α phase, β phase and grain boundary (GB) regions, in which the GB region was a visualised representation of GBS. The quantitative strength ratio between the GB regions and α phase was calculated according to the Zener–Holloman parameter Z and grain size, which determined the microscopic deformation behaviour. There were found to be two high microscopic strain regions in the α phase: intragranular deformation bands through the most favourable slipping and near the GBs through multiple slipping, which promoted continuous and discontinuous DRX, respectively. With the decrease in parameter Z or grain size, the activated dislocations accommodating GBS were found to no longer pile up inside the grain, but instead travel across the grain interior. Finally, methods to improve the macroscopic plastic formability were proposed for the difficult-to-form titanium alloys experiencing non-superplastic hot deformation.

Micromechanism of Cold Deformation of Two-Phase Polycrystalline Ti–Al Alloy with Void

Micromechanisms of Deformation and Fracture in a Ti3Al-Nb Alloy

Microstructural Evolution and Deformation Micromechanism of Cold-Deformed TiNi-Based Alloys

Study of deformation micromechanism in cold-deformed TiNi based alloys

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Deformation and Phase Transformation of Disordered α Phase in the (α + γ) Two-Phase Region of a High-Nb TiAl Alloy

Effect of deformation and cooling on non-equilibrium microstructure evolution and phase-transition mechanism of Ti–6Al-2.5Mo-1.5Cr-0.5Fe-0.3Si

Unraveling hot deformation behavior and microstructure evolution of nanolamellar TiAl/Ti3Al composites

Deformation-induced Microstructure Refinement in Primary Α Phase-Containing Ti–10V–2Fe–3Al Alloy

A Study on Deformation Mechanisms of Ti2AlNb-Based Alloy Under Plane Strain Compression

Recent Advances on the Deformation Behavior of Two-Phase α+β Titanium Alloys

Studying Plastic Deformation Mechanism in β-Ti-Nb Alloys by Molecular Dynamic Simulations

Concentration-Dependent High-Temperature Deformation Mechanism of Hexagonal Close-Packed Ti-Al Alloys

Texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr dual-phase alloy during cold rolling based on multiscale crystal plasticity finite element model

Microstructural characteristics and recrystallization mechanism of Ti-6.5Al–2Zr–1Mo–1V alloy during two-stage hot deformation

Low Strain Rate Deformation Study in a Two-Phase TiAl Based Intermetallic Alloy

Transportation of Dislocation Plasticity in a Dual-Phase TiMo Alloy

Plastic deformation mode and α/β slip transfer of Ti–5Al-2.5Cr-0.5Fe-4.5Mo–1Sn–2Zr–3Zn titanium alloy at room temperature

Molecular Dynamics Simulation Of Deformation-Induced Crystallization Mechanism In Amorphous Ti3al Alloy

An Investigation on Microstructure Evolution and Deformation Mechanism of Ti–5Al–5Mo–5V–1Cr–1Fe Alloy During In-Situ Tensile

Analysing the Interaction between Microscopic Deformation, Microstructure and Void Evolution of Near-α Titanium Alloys during Non-Superplastic Hot Deformation by an Integrated Crystal Plasticity Finite Element Model