Abstract:An Al-Cu matrix composite reinforced with uniformly-distributed micron- and nano-double-sized TiC particles (MNDS-TiCps) was successfully fabricated using a wire and arc additive manufacturing (WAAM) process. The combined effect of the MNDS-TiCps on the precipitation of the theta '' phase, the structural evolution of the grain boundaries, and solidification dynamics of the deposited Al-Cu matrix composites were subsequently investigated. The micron-sized TiC particles in the molten pool generate nucleation undercooling (Delta T-nu, similar to 0.32 K) which inhibits grain boundary segregation due to constitutional undercooling and promotes the redistribution of the Cu solute in the Al matrix. The phase composition at the grain boundaries changes from theta-Al2Cu to alpha-Al + theta-Al2Cu and the non-coherent interface between the alpha+theta transition zone and theta grain boundary is transformed into a coherent interface between the alpha+theta grain boundary and Al matrix, i.e. (211)(theta-Al2Cu)//(111)(Al). The decrease in free energy within the Al matrix provides energy to facilitate the growth of nuclei on the surface of the nano-sized particles. A semi-coherent interface is thus detected between the TiC and precipitates, characterized by a crystal orientation relationship of (200)(TiC)//(310)(theta ''-Al2Cu). The dislocations that provide pipe-diffusion paths for solute Cu constitute a driving force that coarsens the precipitates, promoting the precipitation of theta '' precipitates. Multi-site co-deformation combined with dislocation increment inhibits stress damage to the micro-interface. The strength and elongation increase by 51.0 % and 118 %, respectively, compared to specimens without TiC. This work provides a novel perspective for tailoring WAAM-deposited Al-Cu alloys by achieving favorable structural evolution in the grain boundaries, inducing the precipitation of precipitates, and yielding outstanding synergy between ductility and strength.

Aluminium-Assisted Alloying of Carbon Steel in Submerged Arc Welding: Application of Al-Cr-Ti-Cu Unconstrained Metal Powders

Aluminium-Assisted Alloying of Carbon Steel in Submerged Arc Welding with Al-Cr-Ni Unconstrained Metal Powders: Thermodynamic Interpretation of Gas Reactions

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Improved Titanium Transfer in Submerged Arc Welding of Carbon Steel through Aluminum Addition

Modification of Flux Oxygen Behaviour via Co-Cr-Al Unconstrained Metal Powder Additions in Submerged Arc Welding: Gas Phase Thermodynamics and 3D Slag SEM Evidence

Application of Copper as Stabiliser in Aluminium Assisted Transfer of Titanium in Submerged Arc Welding of Carbon Steel

Reactions at the molten flux-weld pool interface in submerged arc welding

In Situ Modification of CaF2-SiO2-Al2O3-MgO Flux Applied in the Aluminium-Assisted Transfer of Titanium in the Submerged Arc Welding of Carbon Steel: Process Mineralogy and Thermochemical Analysis

Insight into the Chemical Behaviour of Chromium in CaF2-SiO2-Al2O3-MgO Flux Applied in Aluminium-Assisted Alloying of Carbon Steel in Submerged Arc Welding

Limits on Ti Element Transfer in Submerged Arc Welding: Thermochemical Analysis

Effect of Alloying Powders on Microstructure and Mechanical Properties of Aluminum Alloy Arc Additive Manufacturing

Wire arc direct energy deposited multiphase steel through in situ micropowder alloying: mechanical and metallurgical studies

Underwater Wet Welding of High-Strength Low-Alloy Steel Using Self-Shielded Flux-Cored Wire with Highly Exothermic Al/CuO Mixture

Research on Cu-6.6%Al-3.2%Si Alloy by Dual Wire Arc Additive Manufacturing

Realization of synergistic enhancement for fracture strength and ductility by adding TiC particles in wire and arc additive manufacturing 2219 aluminium alloy

Contribution Made by Double-Sized TiC Particles Addition to the Ductility–strength Synergy in Wire and Arc Additively Manufactured Al–Cu Alloys

Fabrication of Fe–30Al alloy using plasma arc welding powered twin-wire directed energy deposition-arc process: Droplet transfer, microstructure, and mechanical property investigation

The Efficiency of Thermite-Assisted Underwater Wet Flux-Cored Arc Welding Process: Electrical Dependence, Microstructural Changes, and Mechanical Properties

The Effect of Alumino-Thermic Addition on Underwater Wet Welding Process Stability

Microstructure, Corrosion and Mechanical Properties of TiC Particles/Al-5Mg Composite Fillers for Tungsten Arc Welding of 5083 Aluminum Alloy

An adapted approach for solidification crack elimination in Al7075 TIG welding