Abstract:Identification of microstructure defects, which are stress concentrators (SC) during the operation of mechanical engineering products, is an important scientific and practical task relevant for manufacturing enterprises. This problem becomes especially urgent and difficult for critical helicopter parts made of sheet TRIP steel VNS9-Sh (23Kh15N5AM3-Sh) and operating under cyclic loads due to the complex microstructure of the steel and small thickness of strips and sheets. To assess the impact of structural defects on the cyclic strength of products made of the steel under study, the specimens were preliminary sorted proceeding from the results of their testing using the method of metal magnetic memory (MMM) and metallographic studies. The MMM method is a structure-sensitive procedure which provides information about the presence of structural defects that arise during the manufacture. Magnetic anomalies in the form of sharp local changes in the intrinsic stray magnetic field (SSMF) ( H ) and its gradient |Δ H | along the length of the controlled section Δ x , were identified on the surface of sheets cut from five different batches. A conventional classification of the identified anomalies was made according to the magnitude of the magnetic field gradient. The specimens of two types were cut in zones of magnetic anomalies and outside them: type 1 — for cyclic tests and type 2 — for metallographic studies. The geometric parameters and field gradient values of magnetic anomalies on specimens of type 1 and type 2 were the same. Metallographic studies in zones of maximum magnetic field gradient on type 2 specimens revealed defects in the form of a strip at the boundary of different structures, which is a structural stress concentrator (SSC) and a source of the inhomogeneity and changes in the magnetic properties. Type 1 specimens with similar magnetic anomalies and Type 1 specimens cut from sheets outside zones of magnetic anomalies were then selected for cyclic testing. Comparative tests for cyclic strength of the specimens with and without specified SSC were carried out. It is shown that the presence of SSC zones in the specimens reduces the number of cycles to failure during cyclic tests by 1 – 2 orders of magnitude compared to the specimens free of SSC. Based on cyclic tensile tests of specimens, a limiting value of the magnetic field gradient was determined that corresponds to the acceptable level of stress concentration on structural defects. This value is recommended for use as a rejection criterion when examining a new tape by the MMM method.

DETERMINATION OF HARDENED METAL LAYER THICKNESS USING MAGNETIC METHOD

Effect of Magnet Thickness on Electromagnetic Performance of High Speed Permanent Magnet Machines

Approach to investigate pre-nucleation fatigue damage of cyclically loaded metals using Vickers microhardness tests

Development of a metal magnetic memory method

A NEW APPROACH TO THE DETECTION OF FATIGUE DAMAGE IN RAILS USING PIEZOMAGNETIC EFFECTS

Theoretical and Experimental Investigation on the Magnetomechanical Effect of Steel Bars Subjected to Cyclic Load

Analytical Model for Eddy Current Testing of Thickness of Multi-layered Structures and Experimental Verification

Identification of Magnetomechanical Phenomena in a Degradation Process of Loaded Steel Elements

A Modification of Magnetic Adaptive Testing: Progressive Method for Nondestructive Inspection of Microstructural Changes in Ferromagnetic Constructional Materials

Control of the parameters of the surface layer of steel parts during their processing applying the material homogeneity criterion

Characterization of Magnetic Field in Crack Propagation Stage and Application to Non-Destructive Evaluation

STUDY OF THE APPLICATION OF INDIRECT METHODS OF ASSESSMENT OF CHANGES IN THE THICKNESS OF THE ROLLED CAGE AS A CONSEQUENCE OF THE INFLUENCE OF THE WEAR OF THE ROLLED CAGE EQUIPMENT

The rolling simulation for cold work metal hardening

A Magnetomechanical Model for the Magnetic Memory Method

Testing of Hardness on Long Rail Welded Joint by Means of Magnetic Barkhausen Noise Technique

Yield strength measurement of ferromagnetic materials based on the inverse magnetostrictive effect

Application of the metal magnetic memory method for detection of defects at the initial stage of their development for prevention of failures of power engineering welded steel structures and steam turbine parts

METHODS FOR HARDENING AND IMPROVEMENT OF FATIGUE CHARACTERISTICS OF TITANIUM AND IRON-CHROMIUM NICKEL ALLOY SAMPLES

Layer Approach to Model Fatigue Strength of Surface-Hardened Components

Magnetic Recording Method (MRM) for Nondestructive Evaluation of Ferromagnetic Materials

Identification of structural defects and their impact on the magnetic memory, static and cyclic strength of VNS9-SH thin sheet trip-steel