Abstract:Introduction: The most important task in the development of modern chemical engineering is to improve the quality of metal products and parts made from them, increase their efficiency, reliability, and fatigue life, bring these indicators to the level of world standards, and ensure the competitiveness of domestic products in the foreign market. The structural safety of chemical engineering equipment is largely determined by the operational reliability of its component elements. The most common and progressive way of their manufacture is cold pressing methods, the quality and reliability of which are largely defined by the condition of the gauged bars' surface. At the same time, the performance characteristics of machinery parts and mechanisms are determined mainly by the properties of the surface layers of metal, since all destruction processes, especially during cyclic loading, usually start from the surface and depend on its structure and physical and chemical status. The role of the type of metal surface imperfection increases greatly with corrosion fatigue, which is determined by the formation of protective barrier films. In the absence of stress, these films reduce the rate of corrosion, and during cyclic loading, they are continuously destroyed. In addition, a stress concentration appears that is caused by surface damage, leading to the formation of corrosive cavities on it. In this paper, based on theoretical research, a physical parameter is proposed that controls the corrosion fatigue life of strain-hardened structural materials of chemical engineering, serving as an indicator of the degree of strain hardening under static tension. An analysis of experimental data has confirmed that the technological plastic processing of structural materials, leading to a decrease in the value of this indicator, causes an increase in their resistance to corrosion-fatigue failure. Purpose: The purpose of this work was to identify a physical parameter that controls the corrosion fatigue life of technologically processed structural materials of chemical engineering. Methods: The experimental test procedure included mechanical tests under static and cyclic loading. Structural materials widely used in chemical engineering, prestrained at different degrees, were selected for the study. Static tension tests of standard samples were carried out on ZD 10/90 and UME-10TM machines with a strain rate of 2 × 10-3 sec–1. The samples were loaded at a frequency of 50 Hz using the MIP-8 machine. A widely spread 3% aqueous solution of sea salt was used for testing in a corrosive environment. Results: It has been established that a physical parameter that controls the corrosion fatigue life of materials is the exponent in the equation of the strain hardening curve under static tension. It has been shown that the process of plastic treatment of material, leading to a decrease in its size, causes an increase in its resistance to corrosion-fatigue failure. Conclusion: It has been shown that in order to assess the feasibility of a particular process treatment in order to increase the resistance to corrosion fatigue of structural materials, it is necessary to trace its impact on the value of the strain hardening index under static tension.

METHODS FOR HARDENING AND IMPROVEMENT OF FATIGUE CHARACTERISTICS OF TITANIUM AND IRON-CHROMIUM NICKEL ALLOY SAMPLES

Fatigue hardening/softening behaviour investigated through Vickers microhardness measurement during high-cycle fatigue

A Study of the Back Stress and the Friction Stress Behaviors of Ti-6Al-4V Alloy During Low Cycle Fatigue at Room Temperature

Effects of Different Mechanical Surface Enhancement Techniques on Surface Integrity and Fatigue Properties of Ti-6Al-4V: A Review

Quantitative evaluation of residual stress and microstructural effects on the surface hardness of machined Ti-6Al-4 V alloy with microscopic characterization techniques

Fatigue performance of medical Ti6Al4V alloy after mechanical surface treatments

Stress-sensitive fatigue crack initiation mechanisms of coated titanium alloy

Improvement in fretting wear and fatigue resistance of Ti–6Al–4V by application of several surface treatments and coatings

Surface layer properties and fatigue behavior in Al 7075‐T73 and Ti‐6Al‐4V

Layer Approach to Model Fatigue Strength of Surface-Hardened Components

Wear- and Surface-Fatigue-Mediated Damage During Fretting in a High-Strength Titanium Alloy

Surface Condition Evolution and Fatigue Evaluation after Different Surface Processes for TiAl47Cr2Nb2 Alloy

Forecasting the Corrosion Fatigue Life of Structural Materials in Chemical Engineering

Effect of Diamond Burnishing on Fatigue Behaviour of AISI 304 Chromium-Nickel Austenitic Stainless Steel

Effect of Post-Processing Treatment on Fatigue Performance of Ti6Al4V Alloy Manufactured by Laser Powder Bed Fusion

Explicit correlation between surface integrity and fatigue limit of surface cold worked chromium-nickel austenitic stainless steels

Development of an Energy-Based Experimental Method for Estimation of Fatigue Crack Evolution in Titanium Alloys

Considerations on the Failure Mechanisms at Fatigue Loading of 1018 Steel Samples Coated with Wip-C1 by Cold Spray

CURRENT STATUS AND DEVELOPMENT PROSPECTS OF NANOSTRUCTURING OF DEFORMED METALS AND ALLOYS AND SPRAYED COATINGS

Effect of Ultrasonic Nanocrystal Surface Modification Treatment at Room and High Temperatures on the High-Frequency Fatigue Behavior of Inconel 718 Fabricated by Laser Metal Deposition

Modified Split Mandrel Method and Equipment to Improve the Fatigue Performance of Structural Components with Fastener Holes